1
Refer to the exhibit. What does the "O*E2" from the "O*E2 0.0.0.0/0 [110/1] via 192.168.1.1, 00:05:34, Serial0/0" line represent?
an external OSPF route that will not increment in cost.
Refer to the exhibit. What is the cost of the route to the 10.0.0.0 network?
1786
What three parameters must be indentical between OSPF routers in order to form an adjacency? (Choose three.)
area id
hello interval
network type
What does OSPF use to reduce the number of exchanges of routing information in networks where large numbers of neighbors are present? (Choose two.)
designated router
backup designated router
What does OSPF use to calculate the cost to a destination network?
bandwidth
A fully converged five router OSPF network has been running successfully for several weeks. All configurations have been saved and no static routes are used. If one router looses power and reboots, what information will be in its routing table after the configuration file is loaded but before OSPF has converged?
Routes for connected networks that are operational will be in the routing table.
Refer to the exhibit. Router A is correctly configured for OSPF. Which OSPF configuration statement or set of statements was entered for router B to generate the exhibited routing table?
B(config-router)# network 192.168.1.0 0.0.0.3 area 0
Refer to the exhibit. Which network command or set of sommands will cause OSPF to be enabled to send and receive packets for any R1 interface in the exhibited subnets?
R1(config-router)# network 0.0.0.0 255.255.255.255 area 0
Refer to the exhibit. What does the "2" stand for in the router ospf 2 statement?
The number 2 identifies this particular instance of OSPF on this router.
Refer to the exhibit. All routers have been configured with the interface priorities that are shown. All routers were restarted simultaneously. The results of the DR/BDR election are shown. What can be concluded about this network?
The highest router ID was most likely determined via an OSPF router-id statement or statements.
Refer to the exhibit. What configuration statements would give the results that are shown in the output of the show ip protocols command?
B(config)# router ospf 1
B(config-router)# router-id 192.168.1.5
Refer to the exhibit. How many OSPF adjacencies must be formed to build the complete topology if a DR or BDR were not elected in this OSPF network?
6
What is the default administrative distance for OSPF?
110
Refer to the exhibit. Routers A, B, C, and D are all running OSPF with default router IDs and OSPF interface priorities. Loopback interfaces are not configured and all interfaces are operational. Router D is the DR and router C is the BDR.
What happens immediately after the following commands are entered on router A?
A(config)# interface fa0/0
A(config-if)# ip ospf priority 255
D will remain the DR. C will remain the BDR.
Refer to the exhibit. All routers are running OSPF. What cost would JAX put in its routing table for the 10.0.0.0/24 network?
1787
What range of networks will be advertised in the OSPF updates by the command Router1(config-router)# network 192.168.0.0 0.0.15.255 area 100?
192.168.0.0/24 through 192.168.15.0/24
Refer to the exhibit. The network administrator wants to set the router ID of Router1 to 192.168.100.1. What steps must the administrator take to accomplish this?
nothing, the router-id of Router1 is already 192.168.100.1
Refer to the exhibit. When OSPF is operational in the exhibited network, what neighbor relationship is developed between Router1 and Router2?
A FULL adjacency is formed.
Refer to the exhibit. Assuming that the routers have default interface OSPF priorities and no configured loopback interfaces, what two roles will router B play on each network segment? (Choose two.)
DR for network 192.168.1.200
BDR for network 192.168.1.204
Refer to the exhibit. Router1 and Router2 are running OSPF. The show ip ospf neighbor command reveals no neighbors. What is a possible cause?
OSPF hello or dead timers do not match.
Refer to the exhibit. Which command sequence on RouterB will redistribute a gateway of last resort to the other routers in OSPF area 0?
RouterB(config)# ip route 0.0.0.0 0.0.0.0 172.16.6.6
RouterB(config)# router ospf 10
RouterB(config-router)# default-information originate
Refer to the exhibit. RouterA, RouterB, and RouterC in the diagram are running OSPF on their Ethernet interfaces. Router D was just added to the network. Routers are configured with the loopback interfaces (Lo 0) that are shown in the exhibit. What happens to the OSPF DR/BDR after RouterD is added to the network?
There is no change in the DR or BDR until either current DR or BDR goes down.
Which two statements describe the use of OSPF DR/BDR elections? (Choose two.)
Elections are required in broadcast multiaccess networks.
Elections are required in non-broadcast multiaccess networks.
Refer to the exhibit. The routers in the exhibit are using default OSPF configuration settings to advertise all attached networks. If all of the routers start at the same time, what will be the result of the DR and BDR elections for this single area OSPF network? (Choose three.)
Router A will be DR for 10.4.0.0/16.
HQ will be BDR for 10.4.0.0/16.
Remote will be DR for 10.5.0.0/16.
Refer to the exhibit. What must be received between neighbors to prevent the dead time that is shown in the exhibit from reaching zero?
hello packets
Friday, June 5, 2009
CCNA 2 Chapter 10
Refer to the exhibit. When Router D is configured to use a link-state routing protocol and is added to the network, what is the first thing that it does to begin learning the network topology?
It learns about its directly connected networks when its interfaces reach the up state.
What two events will cause a link state router to send LSPs to all neighbors? (Choose two.)
whenever the network topology changes
upon initial startup of router or routing protocol
What is the final step in the link state routing process?
SPF computes best path to each destination network
What two statements correctly describe the link state routing process? (Choose two.)
each router in the area floods LSPs to all neighbors
all routers in the area have identical link state databases
Refer to the exhibit. What kind of information would be seen in an LSP sent from router JAX to router ATL?
cost of the link
What feature do modern link-state protocols provide to minimize processing and memory requirements?
splitting routing topologies into smaller areas
To achieve network convergence, what three steps does each link state router take? (Choose three.)
build a Link State Packet (LSP) containing the state of each directly connected link
flood the LSP to all neighbors, who then store all LSPs received in a database
construct a complete map of the topology and compute the best path to each destination network
What speeds up convergence in a network using link-state routing?
updates triggered by network changes
Why is it difficult for routing loops to occur in networks that use link-state routing?
Each router builds a complete and synchronized view of the network.
What are some of the advantages of using a link-state routing protocol instead of a distance vector routing protocol? (Choose two.)
Routers have direct knowledge of all links in the network and how they are connected.
After the inital LSA flooding, they generally require less bandwidth to communicate changes in a topology.
Which algorithm is run by link-state routing protocols to calculate the shortest path to destination networks?
Dijkstra
Refer to the exhibit. Which statement correctly describes the path traffic would take from the 10.0.0.0/24 network to the 192.168.1.0/24 network if a link-state routing protocol was in use?
BOS -> ORL -> JAX -> ATL because this path is the lowest cost
Which database or table must be identical on all link-state routers within an area in order to construct an accurate SPF tree?
link-state database
Which two routing protocols use Dijkstra’s shortest path first algorithm? (Choose two.)
IS-IS
OSPF
When are link-state packets sent to neighbors?
when a link goes up or down
Refer to the exhibit. What does JAX do with link-state packets from ORL?
sends out the individual link-state packets out the interface connected to BOS
A new network administrator is given the task of selecting an appropriate dynamic routing protocol for a software development company. The company has over 100 routers, uses CIDR and VLSM, requires fast convergence, and uses both Cisco and non-Cisco equipment. Which routing protocol is appropriate for this company?
OSPF
What action does a link-state router take immediately upon receipt of an LSP from a neighboring router?
floods the LSP to neighbors
Refer to the exhibit. If all routers and interfaces are configured to use a link-state routing protocol, from which routers will router D receive hello packets?
B and C
It learns about its directly connected networks when its interfaces reach the up state.
What two events will cause a link state router to send LSPs to all neighbors? (Choose two.)
whenever the network topology changes
upon initial startup of router or routing protocol
What is the final step in the link state routing process?
SPF computes best path to each destination network
What two statements correctly describe the link state routing process? (Choose two.)
each router in the area floods LSPs to all neighbors
all routers in the area have identical link state databases
Refer to the exhibit. What kind of information would be seen in an LSP sent from router JAX to router ATL?
cost of the link
What feature do modern link-state protocols provide to minimize processing and memory requirements?
splitting routing topologies into smaller areas
To achieve network convergence, what three steps does each link state router take? (Choose three.)
build a Link State Packet (LSP) containing the state of each directly connected link
flood the LSP to all neighbors, who then store all LSPs received in a database
construct a complete map of the topology and compute the best path to each destination network
What speeds up convergence in a network using link-state routing?
updates triggered by network changes
Why is it difficult for routing loops to occur in networks that use link-state routing?
Each router builds a complete and synchronized view of the network.
What are some of the advantages of using a link-state routing protocol instead of a distance vector routing protocol? (Choose two.)
Routers have direct knowledge of all links in the network and how they are connected.
After the inital LSA flooding, they generally require less bandwidth to communicate changes in a topology.
Which algorithm is run by link-state routing protocols to calculate the shortest path to destination networks?
Dijkstra
Refer to the exhibit. Which statement correctly describes the path traffic would take from the 10.0.0.0/24 network to the 192.168.1.0/24 network if a link-state routing protocol was in use?
BOS -> ORL -> JAX -> ATL because this path is the lowest cost
Which database or table must be identical on all link-state routers within an area in order to construct an accurate SPF tree?
link-state database
Which two routing protocols use Dijkstra’s shortest path first algorithm? (Choose two.)
IS-IS
OSPF
When are link-state packets sent to neighbors?
when a link goes up or down
Refer to the exhibit. What does JAX do with link-state packets from ORL?
sends out the individual link-state packets out the interface connected to BOS
A new network administrator is given the task of selecting an appropriate dynamic routing protocol for a software development company. The company has over 100 routers, uses CIDR and VLSM, requires fast convergence, and uses both Cisco and non-Cisco equipment. Which routing protocol is appropriate for this company?
OSPF
What action does a link-state router take immediately upon receipt of an LSP from a neighboring router?
floods the LSP to neighbors
Refer to the exhibit. If all routers and interfaces are configured to use a link-state routing protocol, from which routers will router D receive hello packets?
B and C
CCNA 2 Chapter 9
On a router running EIGRP, what database would maintain a list of feasible successors?
topology table
Refer to the exhibit. This is the debug output from 2 directly connected EIGRP routers. They are not forming an adjacency. What is the cause?
network 192.168.1.64 0.0.0.3
What two actions will the EIGRP DUAL FSM take if a link to a network goes down? (Choose two.)
query neighbors for a new route
search topology table for a feasible successor
Refer to the exhibit. What is indicated by the P at the beginning of the topology entry?
the route is in a stable state
In which of the following tables does the EIGRP DUAL algorithm store the primary route to a destination? (Choose two.)
routing
topology
What information is maintained in the EIGRP topology database for a destination route? (Choose three.)
the routing protocol
the feasible distance of the route
the route cost as advertised by the neighboring router
Which of the following statements describes the bounded updates used by EIGRP?
Partial updates are sent only to routers that need the information.
Which of the following types of routes will be denoted by EX in EIGRP routing table entries? (Choose two.)
routes learned from other routing protocols
EIGRP routes that originate in different autonomous systems
Host 192.168.1.66 in the network illustrated is unable to ping host 192.168.1.130. How must EIGRP be configured to enable connectivity between the two hosts? (Choose two.)
R1(config-router)# no auto-summary
R2(config-router)# no auto-summary
Which two statements describe characteristics of EIGRP? (Choose two.)
EIGRP is a distance vector routing protocol.
EIGRP supports classless routing and VLSM.
Refer to the exhibit. Based on the output of show ip eigrp neighbors, what are two possible problems with adjacencies between Router1 and Router2? (Choose two.)
The routers are configured with different EIGRP process IDs.
The serial interfaces for both routers are in different networks.
Refer to the exhibit. In the topology table, what do the numbers 3011840 and 3128695 represent?
the total metric for that network as advertised by the EIGRP neighbor
Refer to the exhibit. EIGRP is the only routing protocol enabled on this network. No static routes are configured on this router. What can be concluded about network 198.18.1.0/24 from the exhibited output?
Packets that are destined for 198.18.1.0/24 will be forwarded to 198.18.10.6.
Refer to the exhibit. All interfaces have been configured with the bandwidths that are shown in the exhibit. Assuming that all routers are using a default configuration of EIGRP as their routing protocol, what path will packets take from the 172.16.1.0/16 network to the 192.168.200.0/24 network?
A,B,E
By default, which two metrics are used by EIGRP to determine the best path between networks?
delay
bandwidth
Which term defines a collection of networks under the administrative control of a single entity that presents a common routing policy to the Internet?
autonomous system
Refer to the exhibit. The company is using EIGRP with an autonomous system number of 10. Pings between hosts on networks that are connected to router A and those that are connected to router B are successful. However, users on the 192.168.3.0 network are unable to reach users on the 192.168.1.32 network. What is the most likely cause of this problem?
The routers are not configured in the same EIGRP routing domain.
In the command router eigrp 20, what is the purpose of the number 20?
identifies the autonomous system number this EIGRP process will advertise
The show ip eigrp topology command output on a router displays a successor route and a feasible successor route to network 192.168.1.0/24. In order to reduce processor utilization, what does EIGRP do when the primary route to this network fails?
The backup route to network 192.168.1.0/24 is installed in the routing table.
What administrative distance would a router assign to a default route in EIGRP that is learned from a source external to the autonomous system?
170
Refer to the exhibit. Network 192.168.0.0/28 goes down. What type of packet does Router2 immediately send to Router1 and Router3?
unicast update packets to 192.168.1.1 and 192.168.2.1
topology table
Refer to the exhibit. This is the debug output from 2 directly connected EIGRP routers. They are not forming an adjacency. What is the cause?
network 192.168.1.64 0.0.0.3
What two actions will the EIGRP DUAL FSM take if a link to a network goes down? (Choose two.)
query neighbors for a new route
search topology table for a feasible successor
Refer to the exhibit. What is indicated by the P at the beginning of the topology entry?
the route is in a stable state
In which of the following tables does the EIGRP DUAL algorithm store the primary route to a destination? (Choose two.)
routing
topology
What information is maintained in the EIGRP topology database for a destination route? (Choose three.)
the routing protocol
the feasible distance of the route
the route cost as advertised by the neighboring router
Which of the following statements describes the bounded updates used by EIGRP?
Partial updates are sent only to routers that need the information.
Which of the following types of routes will be denoted by EX in EIGRP routing table entries? (Choose two.)
routes learned from other routing protocols
EIGRP routes that originate in different autonomous systems
Host 192.168.1.66 in the network illustrated is unable to ping host 192.168.1.130. How must EIGRP be configured to enable connectivity between the two hosts? (Choose two.)
R1(config-router)# no auto-summary
R2(config-router)# no auto-summary
Which two statements describe characteristics of EIGRP? (Choose two.)
EIGRP is a distance vector routing protocol.
EIGRP supports classless routing and VLSM.
Refer to the exhibit. Based on the output of show ip eigrp neighbors, what are two possible problems with adjacencies between Router1 and Router2? (Choose two.)
The routers are configured with different EIGRP process IDs.
The serial interfaces for both routers are in different networks.
Refer to the exhibit. In the topology table, what do the numbers 3011840 and 3128695 represent?
the total metric for that network as advertised by the EIGRP neighbor
Refer to the exhibit. EIGRP is the only routing protocol enabled on this network. No static routes are configured on this router. What can be concluded about network 198.18.1.0/24 from the exhibited output?
Packets that are destined for 198.18.1.0/24 will be forwarded to 198.18.10.6.
Refer to the exhibit. All interfaces have been configured with the bandwidths that are shown in the exhibit. Assuming that all routers are using a default configuration of EIGRP as their routing protocol, what path will packets take from the 172.16.1.0/16 network to the 192.168.200.0/24 network?
A,B,E
By default, which two metrics are used by EIGRP to determine the best path between networks?
delay
bandwidth
Which term defines a collection of networks under the administrative control of a single entity that presents a common routing policy to the Internet?
autonomous system
Refer to the exhibit. The company is using EIGRP with an autonomous system number of 10. Pings between hosts on networks that are connected to router A and those that are connected to router B are successful. However, users on the 192.168.3.0 network are unable to reach users on the 192.168.1.32 network. What is the most likely cause of this problem?
The routers are not configured in the same EIGRP routing domain.
In the command router eigrp 20, what is the purpose of the number 20?
identifies the autonomous system number this EIGRP process will advertise
The show ip eigrp topology command output on a router displays a successor route and a feasible successor route to network 192.168.1.0/24. In order to reduce processor utilization, what does EIGRP do when the primary route to this network fails?
The backup route to network 192.168.1.0/24 is installed in the routing table.
What administrative distance would a router assign to a default route in EIGRP that is learned from a source external to the autonomous system?
170
Refer to the exhibit. Network 192.168.0.0/28 goes down. What type of packet does Router2 immediately send to Router1 and Router3?
unicast update packets to 192.168.1.1 and 192.168.2.1
CCNA 2 Chapter 8
Refer to the exhibit. What can be determined from this output?
All of the routes listed are network routes.
Refer to the exhibit. A packet destined for host 128.107.0.5/16 is processed by the JAX router. After finding the static route in the routing table that matches the destination network for this packet, what does the router do next?
performs a recursive lookup to find the exit interface used to forward the packet
Refer to the exhibit. What parent network will automatically be included in the routing table when the three subnets are configured on Router1?
172.16.0.0/16
The following entry is displayed in the routing table:
R 192.168.8.0/24 [120/2] via 192.168.4.1, 00:00:26, Serial0/0/1
What type of route is this?
a level 1 ultimate network route
Refer to the exhibit. Router1 is running IOS version 12.2. What will the network administrator need to do so that packets for unknown child routes of 172.16.0.0/24 will not be dropped?
do nothing, ip classless is on by default
Refer to the exhibit. Router B receives a packet with a destination address of 10.16.1.97. What will router B do?
use the default route
Refer to the exhibit. How many routes in this output qualify for use as ultimate routes?
7
Refer to the exhibit. With the ip classless command issued, what will router R2 do with a packet destined for host 172.16.4.234?
send packet out Serial 0/0/1
Refer to the exhibit. Which statement correctly describes this network?
There is at least one parent and one child route
Refer to the exhibit. Router1 has been issued the ip classless command. What happens to packets destined to host 172.16.3.10?
forward out interface Serial0/0/1
Refer to the exhibit. The network administrator has discovered that packets destined for servers on the 172.16.254.0 network are being dropped by Router2. What command should the administrator issue to ensure that these packets are sent out the gateway of last resort, Serial 0/0/1?
ip classless
A router has the following entries in its routing table:
S 192.168.0.0/24 [1/0] via 192.168.128.2
O 192.168.0.0/25 [110/2175] via 172.16.1.1, 00:02:15, FastEthernet0/1
D 192.168.0.0/25 [90/22455] via 172.16.2.2, 00:12:15, Serial0/0/0
R 192.168.0.0/26 [120/2] via 172.16.3.3, 00:00:15, Serial0/0/1
The router receives a packet that is destined for a host with the address 192.168.0.58. Which route would this router use to forward the packet?
the RIP route
What determines if the router implements a classless route lookup process?
Multiple routes with different masks to the same destination are in the routing table.
What occurs when no ip classless is implemented on the router?
The router will assume it has knowledge of all subnets in the network and will not search beyond child routes for a better match.
Refer to the exhibit. The graphic contains partial contents of the routing table on router E. Router E is running version 12.3 of the IOS and is configured for default routing behavior. Router E receives a packet to forward. Which route in the routing table will be searched
first and why?
172.16.0.0/25 because it is the first level 1 route
A network is converged and the routing tables are complete. When a packet needs to be forwarded, what is the first criterion used to determine the best path in the routing table?
the route with the longest address and mask match to the destination
Refer to the exhibit. What subnet mask will Router1 apply to child routes of the 172.16.0.0/24 network?
255.255.255.0
Refer to the exhibit. What protocol was used to distribute the routing information for the network 172.16.1.4?
RIPv2
A route to a destination network is learned from multiple routing protocols. What is used by a Cisco router to select the preferred route to the destination that will be installed in the routing table?
administrative distance
All of the routes listed are network routes.
Refer to the exhibit. A packet destined for host 128.107.0.5/16 is processed by the JAX router. After finding the static route in the routing table that matches the destination network for this packet, what does the router do next?
performs a recursive lookup to find the exit interface used to forward the packet
Refer to the exhibit. What parent network will automatically be included in the routing table when the three subnets are configured on Router1?
172.16.0.0/16
The following entry is displayed in the routing table:
R 192.168.8.0/24 [120/2] via 192.168.4.1, 00:00:26, Serial0/0/1
What type of route is this?
a level 1 ultimate network route
Refer to the exhibit. Router1 is running IOS version 12.2. What will the network administrator need to do so that packets for unknown child routes of 172.16.0.0/24 will not be dropped?
do nothing, ip classless is on by default
Refer to the exhibit. Router B receives a packet with a destination address of 10.16.1.97. What will router B do?
use the default route
Refer to the exhibit. How many routes in this output qualify for use as ultimate routes?
7
Refer to the exhibit. With the ip classless command issued, what will router R2 do with a packet destined for host 172.16.4.234?
send packet out Serial 0/0/1
Refer to the exhibit. Which statement correctly describes this network?
There is at least one parent and one child route
Refer to the exhibit. Router1 has been issued the ip classless command. What happens to packets destined to host 172.16.3.10?
forward out interface Serial0/0/1
Refer to the exhibit. The network administrator has discovered that packets destined for servers on the 172.16.254.0 network are being dropped by Router2. What command should the administrator issue to ensure that these packets are sent out the gateway of last resort, Serial 0/0/1?
ip classless
A router has the following entries in its routing table:
S 192.168.0.0/24 [1/0] via 192.168.128.2
O 192.168.0.0/25 [110/2175] via 172.16.1.1, 00:02:15, FastEthernet0/1
D 192.168.0.0/25 [90/22455] via 172.16.2.2, 00:12:15, Serial0/0/0
R 192.168.0.0/26 [120/2] via 172.16.3.3, 00:00:15, Serial0/0/1
The router receives a packet that is destined for a host with the address 192.168.0.58. Which route would this router use to forward the packet?
the RIP route
What determines if the router implements a classless route lookup process?
Multiple routes with different masks to the same destination are in the routing table.
What occurs when no ip classless is implemented on the router?
The router will assume it has knowledge of all subnets in the network and will not search beyond child routes for a better match.
Refer to the exhibit. The graphic contains partial contents of the routing table on router E. Router E is running version 12.3 of the IOS and is configured for default routing behavior. Router E receives a packet to forward. Which route in the routing table will be searched
first and why?
172.16.0.0/25 because it is the first level 1 route
A network is converged and the routing tables are complete. When a packet needs to be forwarded, what is the first criterion used to determine the best path in the routing table?
the route with the longest address and mask match to the destination
Refer to the exhibit. What subnet mask will Router1 apply to child routes of the 172.16.0.0/24 network?
255.255.255.0
Refer to the exhibit. What protocol was used to distribute the routing information for the network 172.16.1.4?
RIPv2
A route to a destination network is learned from multiple routing protocols. What is used by a Cisco router to select the preferred route to the destination that will be installed in the routing table?
administrative distance
CCNA 2 Chapter 7
Refer to the exhibit. If all routers are running RIP version 2, why is there no route for the 192.168.1.32/27 network?
Rip version 2 will auto summarize routes by default.
Refer to the exhibit. Which two statements are true? (Choose two.)
Router1 will install a route to 192.168.0.0/20
Router2 will not install a route to 192.168.16.0/20
Refer to the exhibit. Which command on which router will allow Router1 to learn about the 192.168.0.0/20 network?
Router2(config-router)# version 2
What are two reasons to implement RIP version 2 rather than RIP version 1? (Choose two.)
RIP version 2 supports VLSM.
RIP version 2 supports routing update authentication.
How are RIP v1 and RIP v2 similar to one another? (Choose three.)
They both use hop count as a metric.
They both have the same metric value for infinite distance.
They both use split horizon to prevent routing loops.
Refer to the exhibit. Routers East and West are configured using RIPv1. Both routers are sending updates about their directly connected routes. The East router can ping the West router serial interface and West can ping the serial interface of East. However, neither router has dynamically learned routes from the other. What is most likely the problem?
VLSM is not supported by RIPv1.
Refer to the exhibit. Which command will allow Router2 to learn about the 192.168.16.0/28 network?
Router1(config-router)# network 192.168.16.0
Refer to the exhibit. All routers are running RIP version 2. JAX is configured to just advertise the 10.0.0.0/24 network. CHI is configured to advertise the 172.16.0.0/16 network. A network administrator enters the commands shown in the exhibit. What changes will occur in
this network?
The CHI router will install a route to the 192.168.0.0/16 network in its routing table.
Refer to the exhibit. A technician needs to add a new loopback interface to test routing functionality and network design. The technician enters the following set of commands on the router:
Sanford(config)# interface loopback1
Sanford(config-if)# ip address 192.168.6.62 255.255.255.252
Why does the router respond with an error?
The network address for Loopback1 overlaps with an already configured interface address.
What is the maximum network diameter permitted by the default metric of RIPv2?
15 hops
What are two functions of the network command used when configuring routing protocols? (Choose two.)
identifies which networks will be included in the routing updates
determines which interfaces can send and receive routing updates
Refer to the exhibit. What can be concluded from the output shown in the exhibit?
The no auto-summary has not been configured on this router.
A network administrator has been told that the company IP address infrastructure must adhere to RFC 1918. What three IP address ranges from RFC 1918 could the administrator use on the network? (Choose three.)
10.0.0.0/8
172.16.0.0/12
192.168.0.0/16
Refer to the exhibit. All routers are running RIPv1. What changes will occur in the routing table of router B if a loopback interface with an address of 10.16.1.129/27 is configured on router B?
A connected route to the 10.16.1.128/27 network is added.
A network administrator installed four new routers that are running RIPv2. Router1 is a boundary router in the RIPv2 network and has a default route configured. Once the network has converged, the network administrator enters Router1(config-router)# defaultinformation
originate on Router1. How will this affect the network?
propagates the default route to all routers in the network
Refer to the exhibit. The exhibited network contains a mixture of Cisco and non-Cisco routers. The command debug ip rip was entered on the JAX router. All routers are running the same version of RIP. Router CHI and Router ORL are not able to reach the 192.168.1.16/28 network. What is a possible solution to this problem?
Configure RIPv2 on routers.
What field was added to the RIP message header by RFC 1723 to add support for VLSM and CIDR?
subnet mask
Refer to the exhibit. What effect will the commands that are shown have on RIP updates for Router1?
Only version 2 updates are sent to 224.0.0.9.
Refer to the exhibit. RIPv1 is configured as the routing protocol for the network that is shown. The following commands are used on each router:
router rip
network 10.0.0.0
network 172.16.0.0
When this configuration is complete, users on the LAN of each router are unable to access the remote LANs. Why?
RIPv1 is unable to route to discontiguous subnets of a major network.
RIPv2 is the configured routing protocol on the routers in a network. The command Router(config-router)# no version 2 is entered on the routers. What effect does entering this command have on routing updates?
Version 1 and 2 updates will be received and the version 2 updates will not be sent.
Rip version 2 will auto summarize routes by default.
Refer to the exhibit. Which two statements are true? (Choose two.)
Router1 will install a route to 192.168.0.0/20
Router2 will not install a route to 192.168.16.0/20
Refer to the exhibit. Which command on which router will allow Router1 to learn about the 192.168.0.0/20 network?
Router2(config-router)# version 2
What are two reasons to implement RIP version 2 rather than RIP version 1? (Choose two.)
RIP version 2 supports VLSM.
RIP version 2 supports routing update authentication.
How are RIP v1 and RIP v2 similar to one another? (Choose three.)
They both use hop count as a metric.
They both have the same metric value for infinite distance.
They both use split horizon to prevent routing loops.
Refer to the exhibit. Routers East and West are configured using RIPv1. Both routers are sending updates about their directly connected routes. The East router can ping the West router serial interface and West can ping the serial interface of East. However, neither router has dynamically learned routes from the other. What is most likely the problem?
VLSM is not supported by RIPv1.
Refer to the exhibit. Which command will allow Router2 to learn about the 192.168.16.0/28 network?
Router1(config-router)# network 192.168.16.0
Refer to the exhibit. All routers are running RIP version 2. JAX is configured to just advertise the 10.0.0.0/24 network. CHI is configured to advertise the 172.16.0.0/16 network. A network administrator enters the commands shown in the exhibit. What changes will occur in
this network?
The CHI router will install a route to the 192.168.0.0/16 network in its routing table.
Refer to the exhibit. A technician needs to add a new loopback interface to test routing functionality and network design. The technician enters the following set of commands on the router:
Sanford(config)# interface loopback1
Sanford(config-if)# ip address 192.168.6.62 255.255.255.252
Why does the router respond with an error?
The network address for Loopback1 overlaps with an already configured interface address.
What is the maximum network diameter permitted by the default metric of RIPv2?
15 hops
What are two functions of the network command used when configuring routing protocols? (Choose two.)
identifies which networks will be included in the routing updates
determines which interfaces can send and receive routing updates
Refer to the exhibit. What can be concluded from the output shown in the exhibit?
The no auto-summary has not been configured on this router.
A network administrator has been told that the company IP address infrastructure must adhere to RFC 1918. What three IP address ranges from RFC 1918 could the administrator use on the network? (Choose three.)
10.0.0.0/8
172.16.0.0/12
192.168.0.0/16
Refer to the exhibit. All routers are running RIPv1. What changes will occur in the routing table of router B if a loopback interface with an address of 10.16.1.129/27 is configured on router B?
A connected route to the 10.16.1.128/27 network is added.
A network administrator installed four new routers that are running RIPv2. Router1 is a boundary router in the RIPv2 network and has a default route configured. Once the network has converged, the network administrator enters Router1(config-router)# defaultinformation
originate on Router1. How will this affect the network?
propagates the default route to all routers in the network
Refer to the exhibit. The exhibited network contains a mixture of Cisco and non-Cisco routers. The command debug ip rip was entered on the JAX router. All routers are running the same version of RIP. Router CHI and Router ORL are not able to reach the 192.168.1.16/28 network. What is a possible solution to this problem?
Configure RIPv2 on routers.
What field was added to the RIP message header by RFC 1723 to add support for VLSM and CIDR?
subnet mask
Refer to the exhibit. What effect will the commands that are shown have on RIP updates for Router1?
Only version 2 updates are sent to 224.0.0.9.
Refer to the exhibit. RIPv1 is configured as the routing protocol for the network that is shown. The following commands are used on each router:
router rip
network 10.0.0.0
network 172.16.0.0
When this configuration is complete, users on the LAN of each router are unable to access the remote LANs. Why?
RIPv1 is unable to route to discontiguous subnets of a major network.
RIPv2 is the configured routing protocol on the routers in a network. The command Router(config-router)# no version 2 is entered on the routers. What effect does entering this command have on routing updates?
Version 1 and 2 updates will be received and the version 2 updates will not be sent.
CCNA 2 Chapter 6
What two advantages does CIDR provide to a network? (Choose two.)
reduced routing table size
reduced routing update traffic
Refer to the exhibit. The network administrator wants to create a subnet for the point-to-point connection between the two routers. Which subnetwork mask would provide enough addresses for the point-to-point link with the least number of wasted addresses?
255.255.255.252
Refer to the exhibit. A network engineer is summarizing the two groups of routes on router R1 shown in the exhibit. Which summarization will work for all the subnets?
192.168.0.0/21
Which of the following are contained in the routing updates of classless routing protocols? (Choose two.)
32-bit address
subnet mask
Which of the following problems does VLSM help to alleviate?
the shortage of IP addresses
What does VLSM allow a network administrator to do?
utilize multiple subnet masks in the same IP address space
Refer to the exhibit. What subnet mask will be applied if Router A sends a RIPv1 update for the network 172.16.1.0 to Router B?
24
Refer to the exhibit. The network administrator wants to minimize the number of entries in Router1’s routing table. What should the administrator implement on the network?
CIDR
A router has a summary route to network 192.168.32.0/20 installed in its routing table. What range of networks are summarized by this route?
192.168.32.0 – 192.168.47.0/24
A network administrator is tasked with dividing up a class C network among the QA, Sales, and Administration departments. The QA department is made up of 10 people, the Sales is made up of 28 people, and the Administration has 6. Which two subnets masks adequately address the QA and Sales departments? (Choose two.)
255.255.255.224 for Sales
255.255.255.240 for QA
In the network shown in the graphic, three bits were borrowed from the host portion of a Class C address. How many valid host addresses will be unused on the three point-to-point links combined if VLSM is not used?
84
A Class C address has been assigned for use in the network shown in the graphic. Using VLSM, which bit mask should be used to provide for the number of host addresses required on Router A, while wasting the fewest addresses?
/27
An additional subnet is required for a new Ethernet link between Router1 and Router2 as shown in the diagram. Which of the following subnet addresses can be configured in this network to provide a maximum of 14 useable addresses for this link while wasting the fewest addresses?
192.1.1.224/28
Which three interior routing protocols support VLSM? (Choose three.)
OSPF
RIP v2
EIGRP
Refer to the exhibit. The number of required host addresses for each subnet in a network is listed in the exhibit. This number includes the host address requirements for all router ports and hosts on that subnet. After all device and router port address assignments are determined, what will be the total number of unused host addresses available?
29
Refer to the exhibit. In the network that is shown, the router interfaces are assigned the first address in each subnet. Which IP address would be usable for a host on one of the LANs in this network?
192.168.2.130/25
Refer to the exhibit. Which address is a broadcast address for one of the subnets that are shown in the exhibit?
192.168.4.15/29
Refer to the exhibit. A network administrator needs to create two subnetworks from 10.0.0.0/8 for a router running RIPv2. The Admin subnet requires 120 hosts and the Sales subnet requires 58 hosts. The network administrator assigned 10.0.1.128/25 to the Admin subnet. The Sales subnet is given 10.0.1.192/26. What will be the result of this addressing scheme?
Because RIPv2 does not support VLSM, the subnet masks will not be allowed.
The subnets overlap and will be rejected by the router.
Refer to the exhibit. A network technician enters the static route in R1 needed to reach network 10.1.1.0/24. A ping from the S0/0/0 interface on R1 to host B fails. The technician begins testing the network and has the following results:
1. pings from R1 to the S0/0/0 interface on R2....successful
2. pings from R1 to the Fa0/0 interface on R2....successful
3. pings from host B to hosts on the 10.1.1.0/24 network....successful
4. pings from host B to the Fa0/0 interface on R2....successful
5. pings from R2 to host B....successful.
The default gateway on host B is not correctly set.
What is a supernet?
a summarization of classful addresses
reduced routing table size
reduced routing update traffic
Refer to the exhibit. The network administrator wants to create a subnet for the point-to-point connection between the two routers. Which subnetwork mask would provide enough addresses for the point-to-point link with the least number of wasted addresses?
255.255.255.252
Refer to the exhibit. A network engineer is summarizing the two groups of routes on router R1 shown in the exhibit. Which summarization will work for all the subnets?
192.168.0.0/21
Which of the following are contained in the routing updates of classless routing protocols? (Choose two.)
32-bit address
subnet mask
Which of the following problems does VLSM help to alleviate?
the shortage of IP addresses
What does VLSM allow a network administrator to do?
utilize multiple subnet masks in the same IP address space
Refer to the exhibit. What subnet mask will be applied if Router A sends a RIPv1 update for the network 172.16.1.0 to Router B?
24
Refer to the exhibit. The network administrator wants to minimize the number of entries in Router1’s routing table. What should the administrator implement on the network?
CIDR
A router has a summary route to network 192.168.32.0/20 installed in its routing table. What range of networks are summarized by this route?
192.168.32.0 – 192.168.47.0/24
A network administrator is tasked with dividing up a class C network among the QA, Sales, and Administration departments. The QA department is made up of 10 people, the Sales is made up of 28 people, and the Administration has 6. Which two subnets masks adequately address the QA and Sales departments? (Choose two.)
255.255.255.224 for Sales
255.255.255.240 for QA
In the network shown in the graphic, three bits were borrowed from the host portion of a Class C address. How many valid host addresses will be unused on the three point-to-point links combined if VLSM is not used?
84
A Class C address has been assigned for use in the network shown in the graphic. Using VLSM, which bit mask should be used to provide for the number of host addresses required on Router A, while wasting the fewest addresses?
/27
An additional subnet is required for a new Ethernet link between Router1 and Router2 as shown in the diagram. Which of the following subnet addresses can be configured in this network to provide a maximum of 14 useable addresses for this link while wasting the fewest addresses?
192.1.1.224/28
Which three interior routing protocols support VLSM? (Choose three.)
OSPF
RIP v2
EIGRP
Refer to the exhibit. The number of required host addresses for each subnet in a network is listed in the exhibit. This number includes the host address requirements for all router ports and hosts on that subnet. After all device and router port address assignments are determined, what will be the total number of unused host addresses available?
29
Refer to the exhibit. In the network that is shown, the router interfaces are assigned the first address in each subnet. Which IP address would be usable for a host on one of the LANs in this network?
192.168.2.130/25
Refer to the exhibit. Which address is a broadcast address for one of the subnets that are shown in the exhibit?
192.168.4.15/29
Refer to the exhibit. A network administrator needs to create two subnetworks from 10.0.0.0/8 for a router running RIPv2. The Admin subnet requires 120 hosts and the Sales subnet requires 58 hosts. The network administrator assigned 10.0.1.128/25 to the Admin subnet. The Sales subnet is given 10.0.1.192/26. What will be the result of this addressing scheme?
Because RIPv2 does not support VLSM, the subnet masks will not be allowed.
The subnets overlap and will be rejected by the router.
Refer to the exhibit. A network technician enters the static route in R1 needed to reach network 10.1.1.0/24. A ping from the S0/0/0 interface on R1 to host B fails. The technician begins testing the network and has the following results:
1. pings from R1 to the S0/0/0 interface on R2....successful
2. pings from R1 to the Fa0/0 interface on R2....successful
3. pings from host B to hosts on the 10.1.1.0/24 network....successful
4. pings from host B to the Fa0/0 interface on R2....successful
5. pings from R2 to host B....successful.
The default gateway on host B is not correctly set.
What is a supernet?
a summarization of classful addresses
CCNA 2 Chapter 5
Refer to the exhibit. The network that is shown is running RIPv1. The 192.168.10.0/24 network was recently added and will only contain end users. What command or set of commands should be entered on Router1 to prevent RIPv1 updates from being sent to the end user devices on the new network while still allowing this new network to be advertised to other routers?
Router1(config-router)# passive-interface fastethernet 0/0
The following line was displayed in the output of the show ip route command.
R 192.168.3.0/24 [120/3] via 192.168.2.2, 00:00:30, Serial0/0
What is the value of the routing metric?
3
Which of the following is considered a limitation of RIP v1?
RIP v1 does not send subnet mask information in its updates.
Refer to the exhibit. The Ethernet interface on Router2 goes down and the administrator notices that the route is still in the Router1 routing table. How much longer will Router1 keep the down network in its routing table before marking it as possibly down?
155 seconds
Refer to the exhibit. Router1 is running RIPv1. What command was entered into Router1 to configure the gateway of last resort?
ip route 0.0.0.0 0.0.0.0 S0/0/1
What are three characteristics of the RIPv1 routing protocol? (Choose three.)
uses hop count as a metric
considers a metric of 16 as infinity
calculates metrics using the Bellman Ford algorithm
Which of the following would be the correct command sequence to enable RIP on Router B for all connected networks?
RouterB(config)# router rip
RouterB(config-router)# network 198.16.4.0
RouterB(config-router)# network 210.36.7.0
RouterB(config-router)# network 220.17.29.0
What is the default update period in seconds for the RIP routing protocol?
30
Refer to the exhibit. What can be concluded from the routing table output of router B?
The default-information originate command has been entered on A.
Refer to the exhibit. A network consists of multiple routers. What can be verified when the show ip protocols command is issued on one of the routers in the network?
routing protocol configuration in use for IP on this router
Refer to the exhibit. All routers are configured with valid interface addresses in the indicated networks and are running RIPv1. The network is converged. Which routes are present in the routing tables?
All routers have all /30 routes. Routers A and E also have some of the /24 routes in their routing table.
Which two statements are true regarding the characteristics of RIPv1? (Choose two).
It is a distance vector routing protocol.
The data portion of a RIP message is encapsulated into a UDP segment.
Which command or set of commands will stop the RIP routing process?
RouterB(config)# no router rip
Refer to the exhibit. All routers in the exhibit are running RIP v1. The network administrator issues the show ip route command on router A. What routes would appear in the routing table output if the network is converged? (Choose two).
R 192.168.2.0/24 [120/1]
R 10.10.1.0/24 [120/2]
Which command will display RIP activity as it occurs on a router?
debug ip rip
Refer to the output from the show ip route command. What can be concluded from the output of this router command?
There are two equal cost paths to network 1.0.0.0.
Refer to the exhibit. Router1 and Router2 are running the RIPv1 protocol. The network administrator configures the command network 10.1.0.0 on Router1. What network will Router1 advertise to Router2?
10.0.0.0/8
Refer to the exhibit. Pings between the serial interfaces of the routers are successful. Hosts on each LAN can ping the Fa0/0 interface of the router to which they are directly connected through the switch. However, pings between hosts on the 10.1.1.0/24 and 10.1.2.0/24 networks are unsuccessful. What is a likely cause of this problem?
RIP is configured incorrectly on R1.
What will happen if an interface IP address is entered for the address portion of the network command in a RIPv1 configuration instead of a network address?
All interfaces in the same classful network as the configured address will be included in the RIPv1 routing process.
Refer to the exhibit. All routers that are shown are running the RIP routing protocol. All unknown IP traffic must be forwarded to the ISP. What router or set of routers are recommended to have both a default route and the default-information originate command issued to implement this forwarding policy?
only the gateway routerRefer to the exhibit. The network that is shown is running RIPv1. The 192.168.10.0/24 network was recently added and will only contain end users. What command or set of commands should be entered on Router1 to prevent RIPv1 updates from being sent to the end user devices on the new network while still allowing this new network to be advertised to other routers?
Router1(config-router)# passive-interface fastethernet 0/0
The following line was displayed in the output of the show ip route command.
R 192.168.3.0/24 [120/3] via 192.168.2.2, 00:00:30, Serial0/0
What is the value of the routing metric?
3
Which of the following is considered a limitation of RIP v1?
RIP v1 does not send subnet mask information in its updates.
Refer to the exhibit. The Ethernet interface on Router2 goes down and the administrator notices that the route is still in the Router1 routing table. How much longer will Router1 keep the down network in its routing table before marking it as possibly down?
155 seconds
Refer to the exhibit. Router1 is running RIPv1. What command was entered into Router1 to configure the gateway of last resort?
ip route 0.0.0.0 0.0.0.0 S0/0/1
What are three characteristics of the RIPv1 routing protocol? (Choose three.)
uses hop count as a metric
considers a metric of 16 as infinity
calculates metrics using the Bellman Ford algorithm
Which of the following would be the correct command sequence to enable RIP on Router B for all connected networks?
RouterB(config)# router rip
RouterB(config-router)# network 198.16.4.0
RouterB(config-router)# network 210.36.7.0
RouterB(config-router)# network 220.17.29.0
What is the default update period in seconds for the RIP routing protocol?
30
Refer to the exhibit. What can be concluded from the routing table output of router B?
The default-information originate command has been entered on A.
Refer to the exhibit. A network consists of multiple routers. What can be verified when the show ip protocols command is issued on one of the routers in the network?
routing protocol configuration in use for IP on this router
Refer to the exhibit. All routers are configured with valid interface addresses in the indicated networks and are running RIPv1. The network is converged. Which routes are present in the routing tables?
All routers have all /30 routes. Routers A and E also have some of the /24 routes in their routing table.
Which two statements are true regarding the characteristics of RIPv1? (Choose two).
It is a distance vector routing protocol.
The data portion of a RIP message is encapsulated into a UDP segment.
Which command or set of commands will stop the RIP routing process?
RouterB(config)# no router rip
Refer to the exhibit. All routers in the exhibit are running RIP v1. The network administrator issues the show ip route command on router A. What routes would appear in the routing table output if the network is converged? (Choose two).
R 192.168.2.0/24 [120/1]
R 10.10.1.0/24 [120/2]
Which command will display RIP activity as it occurs on a router?
debug ip rip
Refer to the output from the show ip route command. What can be concluded from the output of this router command?
There are two equal cost paths to network 1.0.0.0.
Refer to the exhibit. Router1 and Router2 are running the RIPv1 protocol. The network administrator configures the command network 10.1.0.0 on Router1. What network will Router1 advertise to Router2?
10.0.0.0/8
Refer to the exhibit. Pings between the serial interfaces of the routers are successful. Hosts on each LAN can ping the Fa0/0 interface of the router to which they are directly connected through the switch. However, pings between hosts on the 10.1.1.0/24 and 10.1.2.0/24 networks are unsuccessful. What is a likely cause of this problem?
RIP is configured incorrectly on R1.
What will happen if an interface IP address is entered for the address portion of the network command in a RIPv1 configuration instead of a network address?
All interfaces in the same classful network as the configured address will be included in the RIPv1 routing process.
Refer to the exhibit. All routers that are shown are running the RIP routing protocol. All unknown IP traffic must be forwarded to the ISP. What router or set of routers are recommended to have both a default route and the default-information originate command issued to implement this forwarding policy?
only the gateway routerRefer to the exhibit. The network that is shown is running RIPv1. The 192.168.10.0/24 network was recently added and will only contain end users. What command or set of commands should be entered on Router1 to prevent RIPv1 updates from being sent to the end user devices on the new network while still allowing this new network to be advertised to other routers?
Router1(config-router)# passive-interface fastethernet 0/0
The following line was displayed in the output of the show ip route command.
R 192.168.3.0/24 [120/3] via 192.168.2.2, 00:00:30, Serial0/0
What is the value of the routing metric?
3
Which of the following is considered a limitation of RIP v1?
RIP v1 does not send subnet mask information in its updates.
Refer to the exhibit. The Ethernet interface on Router2 goes down and the administrator notices that the route is still in the Router1 routing table. How much longer will Router1 keep the down network in its routing table before marking it as possibly down?
155 seconds
Refer to the exhibit. Router1 is running RIPv1. What command was entered into Router1 to configure the gateway of last resort?
ip route 0.0.0.0 0.0.0.0 S0/0/1
What are three characteristics of the RIPv1 routing protocol? (Choose three.)
uses hop count as a metric
considers a metric of 16 as infinity
calculates metrics using the Bellman Ford algorithm
Which of the following would be the correct command sequence to enable RIP on Router B for all connected networks?
RouterB(config)# router rip
RouterB(config-router)# network 198.16.4.0
RouterB(config-router)# network 210.36.7.0
RouterB(config-router)# network 220.17.29.0
What is the default update period in seconds for the RIP routing protocol?
30
Refer to the exhibit. What can be concluded from the routing table output of router B?
The default-information originate command has been entered on A.
Refer to the exhibit. A network consists of multiple routers. What can be verified when the show ip protocols command is issued on one of the routers in the network?
routing protocol configuration in use for IP on this router
Refer to the exhibit. All routers are configured with valid interface addresses in the indicated networks and are running RIPv1. The network is converged. Which routes are present in the routing tables?
All routers have all /30 routes. Routers A and E also have some of the /24 routes in their routing table.
Which two statements are true regarding the characteristics of RIPv1? (Choose two).
It is a distance vector routing protocol.
The data portion of a RIP message is encapsulated into a UDP segment.
Which command or set of commands will stop the RIP routing process?
RouterB(config)# no router rip
Refer to the exhibit. All routers in the exhibit are running RIP v1. The network administrator issues the show ip route command on router A. What routes would appear in the routing table output if the network is converged? (Choose two).
R 192.168.2.0/24 [120/1]
R 10.10.1.0/24 [120/2]
Which command will display RIP activity as it occurs on a router?
debug ip rip
Refer to the output from the show ip route command. What can be concluded from the output of this router command?
There are two equal cost paths to network 1.0.0.0.
Refer to the exhibit. Router1 and Router2 are running the RIPv1 protocol. The network administrator configures the command network 10.1.0.0 on Router1. What network will Router1 advertise to Router2?
10.0.0.0/8
Refer to the exhibit. Pings between the serial interfaces of the routers are successful. Hosts on each LAN can ping the Fa0/0 interface of the router to which they are directly connected through the switch. However, pings between hosts on the 10.1.1.0/24 and 10.1.2.0/24 networks are unsuccessful. What is a likely cause of this problem?
RIP is configured incorrectly on R1.
What will happen if an interface IP address is entered for the address portion of the network command in a RIPv1 configuration instead of a network address?
All interfaces in the same classful network as the configured address will be included in the RIPv1 routing process.
Refer to the exhibit. All routers that are shown are running the RIP routing protocol. All unknown IP traffic must be forwarded to the ISP. What router or set of routers are recommended to have both a default route and the default-information originate command issued to implement this forwarding policy?
only the gateway routerRefer to the exhibit. The network that is shown is running RIPv1. The 192.168.10.0/24 network was recently added and will only contain end users. What command or set of commands should be entered on Router1 to prevent RIPv1 updates from being sent to the end user devices on the new network while still allowing this new network to be advertised to other routers?
Router1(config-router)# passive-interface fastethernet 0/0
The following line was displayed in the output of the show ip route command.
R 192.168.3.0/24 [120/3] via 192.168.2.2, 00:00:30, Serial0/0
What is the value of the routing metric?
3
Which of the following is considered a limitation of RIP v1?
RIP v1 does not send subnet mask information in its updates.
Refer to the exhibit. The Ethernet interface on Router2 goes down and the administrator notices that the route is still in the Router1 routing table. How much longer will Router1 keep the down network in its routing table before marking it as possibly down?
155 seconds
Refer to the exhibit. Router1 is running RIPv1. What command was entered into Router1 to configure the gateway of last resort?
ip route 0.0.0.0 0.0.0.0 S0/0/1
What are three characteristics of the RIPv1 routing protocol? (Choose three.)
uses hop count as a metric
considers a metric of 16 as infinity
calculates metrics using the Bellman Ford algorithm
Which of the following would be the correct command sequence to enable RIP on Router B for all connected networks?
RouterB(config)# router rip
RouterB(config-router)# network 198.16.4.0
RouterB(config-router)# network 210.36.7.0
RouterB(config-router)# network 220.17.29.0
What is the default update period in seconds for the RIP routing protocol?
30
Refer to the exhibit. What can be concluded from the routing table output of router B?
The default-information originate command has been entered on A.
Refer to the exhibit. A network consists of multiple routers. What can be verified when the show ip protocols command is issued on one of the routers in the network?
routing protocol configuration in use for IP on this router
Refer to the exhibit. All routers are configured with valid interface addresses in the indicated networks and are running RIPv1. The network is converged. Which routes are present in the routing tables?
All routers have all /30 routes. Routers A and E also have some of the /24 routes in their routing table.
Which two statements are true regarding the characteristics of RIPv1? (Choose two).
It is a distance vector routing protocol.
The data portion of a RIP message is encapsulated into a UDP segment.
Which command or set of commands will stop the RIP routing process?
RouterB(config)# no router rip
Refer to the exhibit. All routers in the exhibit are running RIP v1. The network administrator issues the show ip route command on router A. What routes would appear in the routing table output if the network is converged? (Choose two).
R 192.168.2.0/24 [120/1]
R 10.10.1.0/24 [120/2]
Which command will display RIP activity as it occurs on a router?
debug ip rip
Refer to the output from the show ip route command. What can be concluded from the output of this router command?
There are two equal cost paths to network 1.0.0.0.
Refer to the exhibit. Router1 and Router2 are running the RIPv1 protocol. The network administrator configures the command network 10.1.0.0 on Router1. What network will Router1 advertise to Router2?
10.0.0.0/8
Refer to the exhibit. Pings between the serial interfaces of the routers are successful. Hosts on each LAN can ping the Fa0/0 interface of the router to which they are directly connected through the switch. However, pings between hosts on the 10.1.1.0/24 and 10.1.2.0/24 networks are unsuccessful. What is a likely cause of this problem?
RIP is configured incorrectly on R1.
What will happen if an interface IP address is entered for the address portion of the network command in a RIPv1 configuration instead of a network address?
All interfaces in the same classful network as the configured address will be included in the RIPv1 routing process.
Refer to the exhibit. All routers that are shown are running the RIP routing protocol. All unknown IP traffic must be forwarded to the ISP. What router or set of routers are recommended to have both a default route and the default-information originate command issued to implement this forwarding policy?
only the gateway routerRefer to the exhibit. The network that is shown is running RIPv1. The 192.168.10.0/24 network was recently added and will only contain end users. What command or set of commands should be entered on Router1 to prevent RIPv1 updates from being sent to the end user devices on the new network while still allowing this new network to be advertised to other routers?
Router1(config-router)# passive-interface fastethernet 0/0
The following line was displayed in the output of the show ip route command.
R 192.168.3.0/24 [120/3] via 192.168.2.2, 00:00:30, Serial0/0
What is the value of the routing metric?
3
Which of the following is considered a limitation of RIP v1?
RIP v1 does not send subnet mask information in its updates.
Refer to the exhibit. The Ethernet interface on Router2 goes down and the administrator notices that the route is still in the Router1 routing table. How much longer will Router1 keep the down network in its routing table before marking it as possibly down?
155 seconds
Refer to the exhibit. Router1 is running RIPv1. What command was entered into Router1 to configure the gateway of last resort?
ip route 0.0.0.0 0.0.0.0 S0/0/1
What are three characteristics of the RIPv1 routing protocol? (Choose three.)
uses hop count as a metric
considers a metric of 16 as infinity
calculates metrics using the Bellman Ford algorithm
Which of the following would be the correct command sequence to enable RIP on Router B for all connected networks?
RouterB(config)# router rip
RouterB(config-router)# network 198.16.4.0
RouterB(config-router)# network 210.36.7.0
RouterB(config-router)# network 220.17.29.0
What is the default update period in seconds for the RIP routing protocol?
30
Refer to the exhibit. What can be concluded from the routing table output of router B?
The default-information originate command has been entered on A.
Refer to the exhibit. A network consists of multiple routers. What can be verified when the show ip protocols command is issued on one of the routers in the network?
routing protocol configuration in use for IP on this router
Refer to the exhibit. All routers are configured with valid interface addresses in the indicated networks and are running RIPv1. The network is converged. Which routes are present in the routing tables?
All routers have all /30 routes. Routers A and E also have some of the /24 routes in their routing table.
Which two statements are true regarding the characteristics of RIPv1? (Choose two).
It is a distance vector routing protocol.
The data portion of a RIP message is encapsulated into a UDP segment.
Which command or set of commands will stop the RIP routing process?
RouterB(config)# no router rip
Refer to the exhibit. All routers in the exhibit are running RIP v1. The network administrator issues the show ip route command on router A. What routes would appear in the routing table output if the network is converged? (Choose two).
R 192.168.2.0/24 [120/1]
R 10.10.1.0/24 [120/2]
Which command will display RIP activity as it occurs on a router?
debug ip rip
Refer to the output from the show ip route command. What can be concluded from the output of this router command?
There are two equal cost paths to network 1.0.0.0.
Refer to the exhibit. Router1 and Router2 are running the RIPv1 protocol. The network administrator configures the command network 10.1.0.0 on Router1. What network will Router1 advertise to Router2?
10.0.0.0/8
Refer to the exhibit. Pings between the serial interfaces of the routers are successful. Hosts on each LAN can ping the Fa0/0 interface of the router to which they are directly connected through the switch. However, pings between hosts on the 10.1.1.0/24 and 10.1.2.0/24 networks are unsuccessful. What is a likely cause of this problem?
RIP is configured incorrectly on R1.
What will happen if an interface IP address is entered for the address portion of the network command in a RIPv1 configuration instead of a network address?
All interfaces in the same classful network as the configured address will be included in the RIPv1 routing process.
Refer to the exhibit. All routers that are shown are running the RIP routing protocol. All unknown IP traffic must be forwarded to the ISP. What router or set of routers are recommended to have both a default route and the default-information originate command issued to implement this forwarding policy?
only the gateway router
Router1(config-router)# passive-interface fastethernet 0/0
The following line was displayed in the output of the show ip route command.
R 192.168.3.0/24 [120/3] via 192.168.2.2, 00:00:30, Serial0/0
What is the value of the routing metric?
3
Which of the following is considered a limitation of RIP v1?
RIP v1 does not send subnet mask information in its updates.
Refer to the exhibit. The Ethernet interface on Router2 goes down and the administrator notices that the route is still in the Router1 routing table. How much longer will Router1 keep the down network in its routing table before marking it as possibly down?
155 seconds
Refer to the exhibit. Router1 is running RIPv1. What command was entered into Router1 to configure the gateway of last resort?
ip route 0.0.0.0 0.0.0.0 S0/0/1
What are three characteristics of the RIPv1 routing protocol? (Choose three.)
uses hop count as a metric
considers a metric of 16 as infinity
calculates metrics using the Bellman Ford algorithm
Which of the following would be the correct command sequence to enable RIP on Router B for all connected networks?
RouterB(config)# router rip
RouterB(config-router)# network 198.16.4.0
RouterB(config-router)# network 210.36.7.0
RouterB(config-router)# network 220.17.29.0
What is the default update period in seconds for the RIP routing protocol?
30
Refer to the exhibit. What can be concluded from the routing table output of router B?
The default-information originate command has been entered on A.
Refer to the exhibit. A network consists of multiple routers. What can be verified when the show ip protocols command is issued on one of the routers in the network?
routing protocol configuration in use for IP on this router
Refer to the exhibit. All routers are configured with valid interface addresses in the indicated networks and are running RIPv1. The network is converged. Which routes are present in the routing tables?
All routers have all /30 routes. Routers A and E also have some of the /24 routes in their routing table.
Which two statements are true regarding the characteristics of RIPv1? (Choose two).
It is a distance vector routing protocol.
The data portion of a RIP message is encapsulated into a UDP segment.
Which command or set of commands will stop the RIP routing process?
RouterB(config)# no router rip
Refer to the exhibit. All routers in the exhibit are running RIP v1. The network administrator issues the show ip route command on router A. What routes would appear in the routing table output if the network is converged? (Choose two).
R 192.168.2.0/24 [120/1]
R 10.10.1.0/24 [120/2]
Which command will display RIP activity as it occurs on a router?
debug ip rip
Refer to the output from the show ip route command. What can be concluded from the output of this router command?
There are two equal cost paths to network 1.0.0.0.
Refer to the exhibit. Router1 and Router2 are running the RIPv1 protocol. The network administrator configures the command network 10.1.0.0 on Router1. What network will Router1 advertise to Router2?
10.0.0.0/8
Refer to the exhibit. Pings between the serial interfaces of the routers are successful. Hosts on each LAN can ping the Fa0/0 interface of the router to which they are directly connected through the switch. However, pings between hosts on the 10.1.1.0/24 and 10.1.2.0/24 networks are unsuccessful. What is a likely cause of this problem?
RIP is configured incorrectly on R1.
What will happen if an interface IP address is entered for the address portion of the network command in a RIPv1 configuration instead of a network address?
All interfaces in the same classful network as the configured address will be included in the RIPv1 routing process.
Refer to the exhibit. All routers that are shown are running the RIP routing protocol. All unknown IP traffic must be forwarded to the ISP. What router or set of routers are recommended to have both a default route and the default-information originate command issued to implement this forwarding policy?
only the gateway routerRefer to the exhibit. The network that is shown is running RIPv1. The 192.168.10.0/24 network was recently added and will only contain end users. What command or set of commands should be entered on Router1 to prevent RIPv1 updates from being sent to the end user devices on the new network while still allowing this new network to be advertised to other routers?
Router1(config-router)# passive-interface fastethernet 0/0
The following line was displayed in the output of the show ip route command.
R 192.168.3.0/24 [120/3] via 192.168.2.2, 00:00:30, Serial0/0
What is the value of the routing metric?
3
Which of the following is considered a limitation of RIP v1?
RIP v1 does not send subnet mask information in its updates.
Refer to the exhibit. The Ethernet interface on Router2 goes down and the administrator notices that the route is still in the Router1 routing table. How much longer will Router1 keep the down network in its routing table before marking it as possibly down?
155 seconds
Refer to the exhibit. Router1 is running RIPv1. What command was entered into Router1 to configure the gateway of last resort?
ip route 0.0.0.0 0.0.0.0 S0/0/1
What are three characteristics of the RIPv1 routing protocol? (Choose three.)
uses hop count as a metric
considers a metric of 16 as infinity
calculates metrics using the Bellman Ford algorithm
Which of the following would be the correct command sequence to enable RIP on Router B for all connected networks?
RouterB(config)# router rip
RouterB(config-router)# network 198.16.4.0
RouterB(config-router)# network 210.36.7.0
RouterB(config-router)# network 220.17.29.0
What is the default update period in seconds for the RIP routing protocol?
30
Refer to the exhibit. What can be concluded from the routing table output of router B?
The default-information originate command has been entered on A.
Refer to the exhibit. A network consists of multiple routers. What can be verified when the show ip protocols command is issued on one of the routers in the network?
routing protocol configuration in use for IP on this router
Refer to the exhibit. All routers are configured with valid interface addresses in the indicated networks and are running RIPv1. The network is converged. Which routes are present in the routing tables?
All routers have all /30 routes. Routers A and E also have some of the /24 routes in their routing table.
Which two statements are true regarding the characteristics of RIPv1? (Choose two).
It is a distance vector routing protocol.
The data portion of a RIP message is encapsulated into a UDP segment.
Which command or set of commands will stop the RIP routing process?
RouterB(config)# no router rip
Refer to the exhibit. All routers in the exhibit are running RIP v1. The network administrator issues the show ip route command on router A. What routes would appear in the routing table output if the network is converged? (Choose two).
R 192.168.2.0/24 [120/1]
R 10.10.1.0/24 [120/2]
Which command will display RIP activity as it occurs on a router?
debug ip rip
Refer to the output from the show ip route command. What can be concluded from the output of this router command?
There are two equal cost paths to network 1.0.0.0.
Refer to the exhibit. Router1 and Router2 are running the RIPv1 protocol. The network administrator configures the command network 10.1.0.0 on Router1. What network will Router1 advertise to Router2?
10.0.0.0/8
Refer to the exhibit. Pings between the serial interfaces of the routers are successful. Hosts on each LAN can ping the Fa0/0 interface of the router to which they are directly connected through the switch. However, pings between hosts on the 10.1.1.0/24 and 10.1.2.0/24 networks are unsuccessful. What is a likely cause of this problem?
RIP is configured incorrectly on R1.
What will happen if an interface IP address is entered for the address portion of the network command in a RIPv1 configuration instead of a network address?
All interfaces in the same classful network as the configured address will be included in the RIPv1 routing process.
Refer to the exhibit. All routers that are shown are running the RIP routing protocol. All unknown IP traffic must be forwarded to the ISP. What router or set of routers are recommended to have both a default route and the default-information originate command issued to implement this forwarding policy?
only the gateway routerRefer to the exhibit. The network that is shown is running RIPv1. The 192.168.10.0/24 network was recently added and will only contain end users. What command or set of commands should be entered on Router1 to prevent RIPv1 updates from being sent to the end user devices on the new network while still allowing this new network to be advertised to other routers?
Router1(config-router)# passive-interface fastethernet 0/0
The following line was displayed in the output of the show ip route command.
R 192.168.3.0/24 [120/3] via 192.168.2.2, 00:00:30, Serial0/0
What is the value of the routing metric?
3
Which of the following is considered a limitation of RIP v1?
RIP v1 does not send subnet mask information in its updates.
Refer to the exhibit. The Ethernet interface on Router2 goes down and the administrator notices that the route is still in the Router1 routing table. How much longer will Router1 keep the down network in its routing table before marking it as possibly down?
155 seconds
Refer to the exhibit. Router1 is running RIPv1. What command was entered into Router1 to configure the gateway of last resort?
ip route 0.0.0.0 0.0.0.0 S0/0/1
What are three characteristics of the RIPv1 routing protocol? (Choose three.)
uses hop count as a metric
considers a metric of 16 as infinity
calculates metrics using the Bellman Ford algorithm
Which of the following would be the correct command sequence to enable RIP on Router B for all connected networks?
RouterB(config)# router rip
RouterB(config-router)# network 198.16.4.0
RouterB(config-router)# network 210.36.7.0
RouterB(config-router)# network 220.17.29.0
What is the default update period in seconds for the RIP routing protocol?
30
Refer to the exhibit. What can be concluded from the routing table output of router B?
The default-information originate command has been entered on A.
Refer to the exhibit. A network consists of multiple routers. What can be verified when the show ip protocols command is issued on one of the routers in the network?
routing protocol configuration in use for IP on this router
Refer to the exhibit. All routers are configured with valid interface addresses in the indicated networks and are running RIPv1. The network is converged. Which routes are present in the routing tables?
All routers have all /30 routes. Routers A and E also have some of the /24 routes in their routing table.
Which two statements are true regarding the characteristics of RIPv1? (Choose two).
It is a distance vector routing protocol.
The data portion of a RIP message is encapsulated into a UDP segment.
Which command or set of commands will stop the RIP routing process?
RouterB(config)# no router rip
Refer to the exhibit. All routers in the exhibit are running RIP v1. The network administrator issues the show ip route command on router A. What routes would appear in the routing table output if the network is converged? (Choose two).
R 192.168.2.0/24 [120/1]
R 10.10.1.0/24 [120/2]
Which command will display RIP activity as it occurs on a router?
debug ip rip
Refer to the output from the show ip route command. What can be concluded from the output of this router command?
There are two equal cost paths to network 1.0.0.0.
Refer to the exhibit. Router1 and Router2 are running the RIPv1 protocol. The network administrator configures the command network 10.1.0.0 on Router1. What network will Router1 advertise to Router2?
10.0.0.0/8
Refer to the exhibit. Pings between the serial interfaces of the routers are successful. Hosts on each LAN can ping the Fa0/0 interface of the router to which they are directly connected through the switch. However, pings between hosts on the 10.1.1.0/24 and 10.1.2.0/24 networks are unsuccessful. What is a likely cause of this problem?
RIP is configured incorrectly on R1.
What will happen if an interface IP address is entered for the address portion of the network command in a RIPv1 configuration instead of a network address?
All interfaces in the same classful network as the configured address will be included in the RIPv1 routing process.
Refer to the exhibit. All routers that are shown are running the RIP routing protocol. All unknown IP traffic must be forwarded to the ISP. What router or set of routers are recommended to have both a default route and the default-information originate command issued to implement this forwarding policy?
only the gateway routerRefer to the exhibit. The network that is shown is running RIPv1. The 192.168.10.0/24 network was recently added and will only contain end users. What command or set of commands should be entered on Router1 to prevent RIPv1 updates from being sent to the end user devices on the new network while still allowing this new network to be advertised to other routers?
Router1(config-router)# passive-interface fastethernet 0/0
The following line was displayed in the output of the show ip route command.
R 192.168.3.0/24 [120/3] via 192.168.2.2, 00:00:30, Serial0/0
What is the value of the routing metric?
3
Which of the following is considered a limitation of RIP v1?
RIP v1 does not send subnet mask information in its updates.
Refer to the exhibit. The Ethernet interface on Router2 goes down and the administrator notices that the route is still in the Router1 routing table. How much longer will Router1 keep the down network in its routing table before marking it as possibly down?
155 seconds
Refer to the exhibit. Router1 is running RIPv1. What command was entered into Router1 to configure the gateway of last resort?
ip route 0.0.0.0 0.0.0.0 S0/0/1
What are three characteristics of the RIPv1 routing protocol? (Choose three.)
uses hop count as a metric
considers a metric of 16 as infinity
calculates metrics using the Bellman Ford algorithm
Which of the following would be the correct command sequence to enable RIP on Router B for all connected networks?
RouterB(config)# router rip
RouterB(config-router)# network 198.16.4.0
RouterB(config-router)# network 210.36.7.0
RouterB(config-router)# network 220.17.29.0
What is the default update period in seconds for the RIP routing protocol?
30
Refer to the exhibit. What can be concluded from the routing table output of router B?
The default-information originate command has been entered on A.
Refer to the exhibit. A network consists of multiple routers. What can be verified when the show ip protocols command is issued on one of the routers in the network?
routing protocol configuration in use for IP on this router
Refer to the exhibit. All routers are configured with valid interface addresses in the indicated networks and are running RIPv1. The network is converged. Which routes are present in the routing tables?
All routers have all /30 routes. Routers A and E also have some of the /24 routes in their routing table.
Which two statements are true regarding the characteristics of RIPv1? (Choose two).
It is a distance vector routing protocol.
The data portion of a RIP message is encapsulated into a UDP segment.
Which command or set of commands will stop the RIP routing process?
RouterB(config)# no router rip
Refer to the exhibit. All routers in the exhibit are running RIP v1. The network administrator issues the show ip route command on router A. What routes would appear in the routing table output if the network is converged? (Choose two).
R 192.168.2.0/24 [120/1]
R 10.10.1.0/24 [120/2]
Which command will display RIP activity as it occurs on a router?
debug ip rip
Refer to the output from the show ip route command. What can be concluded from the output of this router command?
There are two equal cost paths to network 1.0.0.0.
Refer to the exhibit. Router1 and Router2 are running the RIPv1 protocol. The network administrator configures the command network 10.1.0.0 on Router1. What network will Router1 advertise to Router2?
10.0.0.0/8
Refer to the exhibit. Pings between the serial interfaces of the routers are successful. Hosts on each LAN can ping the Fa0/0 interface of the router to which they are directly connected through the switch. However, pings between hosts on the 10.1.1.0/24 and 10.1.2.0/24 networks are unsuccessful. What is a likely cause of this problem?
RIP is configured incorrectly on R1.
What will happen if an interface IP address is entered for the address portion of the network command in a RIPv1 configuration instead of a network address?
All interfaces in the same classful network as the configured address will be included in the RIPv1 routing process.
Refer to the exhibit. All routers that are shown are running the RIP routing protocol. All unknown IP traffic must be forwarded to the ISP. What router or set of routers are recommended to have both a default route and the default-information originate command issued to implement this forwarding policy?
only the gateway routerRefer to the exhibit. The network that is shown is running RIPv1. The 192.168.10.0/24 network was recently added and will only contain end users. What command or set of commands should be entered on Router1 to prevent RIPv1 updates from being sent to the end user devices on the new network while still allowing this new network to be advertised to other routers?
Router1(config-router)# passive-interface fastethernet 0/0
The following line was displayed in the output of the show ip route command.
R 192.168.3.0/24 [120/3] via 192.168.2.2, 00:00:30, Serial0/0
What is the value of the routing metric?
3
Which of the following is considered a limitation of RIP v1?
RIP v1 does not send subnet mask information in its updates.
Refer to the exhibit. The Ethernet interface on Router2 goes down and the administrator notices that the route is still in the Router1 routing table. How much longer will Router1 keep the down network in its routing table before marking it as possibly down?
155 seconds
Refer to the exhibit. Router1 is running RIPv1. What command was entered into Router1 to configure the gateway of last resort?
ip route 0.0.0.0 0.0.0.0 S0/0/1
What are three characteristics of the RIPv1 routing protocol? (Choose three.)
uses hop count as a metric
considers a metric of 16 as infinity
calculates metrics using the Bellman Ford algorithm
Which of the following would be the correct command sequence to enable RIP on Router B for all connected networks?
RouterB(config)# router rip
RouterB(config-router)# network 198.16.4.0
RouterB(config-router)# network 210.36.7.0
RouterB(config-router)# network 220.17.29.0
What is the default update period in seconds for the RIP routing protocol?
30
Refer to the exhibit. What can be concluded from the routing table output of router B?
The default-information originate command has been entered on A.
Refer to the exhibit. A network consists of multiple routers. What can be verified when the show ip protocols command is issued on one of the routers in the network?
routing protocol configuration in use for IP on this router
Refer to the exhibit. All routers are configured with valid interface addresses in the indicated networks and are running RIPv1. The network is converged. Which routes are present in the routing tables?
All routers have all /30 routes. Routers A and E also have some of the /24 routes in their routing table.
Which two statements are true regarding the characteristics of RIPv1? (Choose two).
It is a distance vector routing protocol.
The data portion of a RIP message is encapsulated into a UDP segment.
Which command or set of commands will stop the RIP routing process?
RouterB(config)# no router rip
Refer to the exhibit. All routers in the exhibit are running RIP v1. The network administrator issues the show ip route command on router A. What routes would appear in the routing table output if the network is converged? (Choose two).
R 192.168.2.0/24 [120/1]
R 10.10.1.0/24 [120/2]
Which command will display RIP activity as it occurs on a router?
debug ip rip
Refer to the output from the show ip route command. What can be concluded from the output of this router command?
There are two equal cost paths to network 1.0.0.0.
Refer to the exhibit. Router1 and Router2 are running the RIPv1 protocol. The network administrator configures the command network 10.1.0.0 on Router1. What network will Router1 advertise to Router2?
10.0.0.0/8
Refer to the exhibit. Pings between the serial interfaces of the routers are successful. Hosts on each LAN can ping the Fa0/0 interface of the router to which they are directly connected through the switch. However, pings between hosts on the 10.1.1.0/24 and 10.1.2.0/24 networks are unsuccessful. What is a likely cause of this problem?
RIP is configured incorrectly on R1.
What will happen if an interface IP address is entered for the address portion of the network command in a RIPv1 configuration instead of a network address?
All interfaces in the same classful network as the configured address will be included in the RIPv1 routing process.
Refer to the exhibit. All routers that are shown are running the RIP routing protocol. All unknown IP traffic must be forwarded to the ISP. What router or set of routers are recommended to have both a default route and the default-information originate command issued to implement this forwarding policy?
only the gateway router
CCNA 2 Chapter 4
Which event will cause a triggered update?
a route is installed in the routing table
Three routers running a distance-vector routing protocol lost all power, including the battery backups. When the routers reload, what will happen?
They will send updates that include only directly connected routes to their directly connected neighbors.
What does the RIP holddown timer do?
instructs routers to ignore updates, for a specified time or event, about possible inaccessible routes
Which two statements are true regarding the function of the RIPv1 routing updates? (Choose two).
updates are broadcast at regular intervals broadcasts are sent to 255.255.255.255
Which of the following statements are correct about RIP?
will send out an update if there is a failure of a link
Which two statements describe EIGRP? (Choose two.)
EIGRP sends triggered updates whenever there is a change in topology that influences the routing information. EIGRP sends a partial routing table update, which includes just routes that have been changed.
Which statement is true regarding cisco’s RIP_JITTER variable?
It prevents the synchronization of routing updates by subtracting a random length of time ranging from 0% to 15% of the specified interval time from the next routing update interval.
What actions will occur after RouterA loses connectivity to network 114.125.16.0? (Choose two.)
RouterB will include network 123.92.76.0 and 136.125.85.0 in its update to RouterA. Router C will learn of the loss of connectivity to network 114.125.16.0 from RouterB.
Which of the following methods does split horizon use to reduce incorrect routing information?
Information learned from one source is not distributed back to that source.
The graphic shows a network that is configured to use RIP routing protocol. Router2 detects that the link to Router1 has gone down. It then advertises the network for this link with a hop count metric of 16. Which routing loop prevention mechanism is in effect?
route poisoning
What is the purpose of the TTL field in the IP header?
limits the time or hops that a packet can traverse through the network before it should be discarded
Which of the following can exist in a distance vector network that has not converged? (Choose three.)
routing loops inconsistent traffic forwarding inconsistent routing table entries
Refer to the exhibit. The routers in this network are running RIP. Router A has not received an update from Router B in over three minutes. How will Router A respond?
The Invalid timer will mark the route as unusable if an update has not been received in 180 seconds.
A network administrator is evaluating RIP versus EIGRP for a new network. The network will be sensitive to congestion and must respond quickly to topology changes. What are two good reasons to choose EIGRP instead of RIP in this case? (Choose two.)
EIGRP only updates affected neighbors. EIGRP updates are partial.
Refer to the exhibit. What path will packets from the 192.168.1.0/24 network travel to reach the 10.0.0.0/8 network if RIP is the active routing protocol?
The path will be router A -> router D -> router E.
Which three routing protocols are distance vector routing protocols? (Choose three).
RIPv1 EIGRP RIPv2
What is a routing loop?
a condition where a packet is constantly transmitted within a series of routers without ever reaching its intended destination
Which two conditions are most likely to cause a routing loop? (Choose two.)
inconsistent routing tables incorrectly configured static routes
What metric does the RIP routing protocol consider to be infinity?
16
What does a router running RIP do first with a new route that is received from an advertisement?
adjusts the metric for the new route to show the added distance for the route
Refer to the exhibit. If all routers are using RIP, how many rounds of updates will occur before all routers know all networks?
3
a route is installed in the routing table
Three routers running a distance-vector routing protocol lost all power, including the battery backups. When the routers reload, what will happen?
They will send updates that include only directly connected routes to their directly connected neighbors.
What does the RIP holddown timer do?
instructs routers to ignore updates, for a specified time or event, about possible inaccessible routes
Which two statements are true regarding the function of the RIPv1 routing updates? (Choose two).
updates are broadcast at regular intervals broadcasts are sent to 255.255.255.255
Which of the following statements are correct about RIP?
will send out an update if there is a failure of a link
Which two statements describe EIGRP? (Choose two.)
EIGRP sends triggered updates whenever there is a change in topology that influences the routing information. EIGRP sends a partial routing table update, which includes just routes that have been changed.
Which statement is true regarding cisco’s RIP_JITTER variable?
It prevents the synchronization of routing updates by subtracting a random length of time ranging from 0% to 15% of the specified interval time from the next routing update interval.
What actions will occur after RouterA loses connectivity to network 114.125.16.0? (Choose two.)
RouterB will include network 123.92.76.0 and 136.125.85.0 in its update to RouterA. Router C will learn of the loss of connectivity to network 114.125.16.0 from RouterB.
Which of the following methods does split horizon use to reduce incorrect routing information?
Information learned from one source is not distributed back to that source.
The graphic shows a network that is configured to use RIP routing protocol. Router2 detects that the link to Router1 has gone down. It then advertises the network for this link with a hop count metric of 16. Which routing loop prevention mechanism is in effect?
route poisoning
What is the purpose of the TTL field in the IP header?
limits the time or hops that a packet can traverse through the network before it should be discarded
Which of the following can exist in a distance vector network that has not converged? (Choose three.)
routing loops inconsistent traffic forwarding inconsistent routing table entries
Refer to the exhibit. The routers in this network are running RIP. Router A has not received an update from Router B in over three minutes. How will Router A respond?
The Invalid timer will mark the route as unusable if an update has not been received in 180 seconds.
A network administrator is evaluating RIP versus EIGRP for a new network. The network will be sensitive to congestion and must respond quickly to topology changes. What are two good reasons to choose EIGRP instead of RIP in this case? (Choose two.)
EIGRP only updates affected neighbors. EIGRP updates are partial.
Refer to the exhibit. What path will packets from the 192.168.1.0/24 network travel to reach the 10.0.0.0/8 network if RIP is the active routing protocol?
The path will be router A -> router D -> router E.
Which three routing protocols are distance vector routing protocols? (Choose three).
RIPv1 EIGRP RIPv2
What is a routing loop?
a condition where a packet is constantly transmitted within a series of routers without ever reaching its intended destination
Which two conditions are most likely to cause a routing loop? (Choose two.)
inconsistent routing tables incorrectly configured static routes
What metric does the RIP routing protocol consider to be infinity?
16
What does a router running RIP do first with a new route that is received from an advertisement?
adjusts the metric for the new route to show the added distance for the route
Refer to the exhibit. If all routers are using RIP, how many rounds of updates will occur before all routers know all networks?
3
CCNA Chapter 4
Which event will cause a triggered update?
a route is installed in the routing table
Three routers running a distance-vector routing protocol lost all power, including the battery backups. When the routers reload, what will happen?
They will send updates that include only directly connected routes to their directly connected neighbors.
What does the RIP holddown timer do?
instructs routers to ignore updates, for a specified time or event, about possible inaccessible routes
Which two statements are true regarding the function of the RIPv1 routing updates? (Choose two).
updates are broadcast at regular intervals broadcasts are sent to 255.255.255.255
Which of the following statements are correct about RIP?
will send out an update if there is a failure of a link
Which two statements describe EIGRP? (Choose two.)
EIGRP sends triggered updates whenever there is a change in topology that influences the routing information. EIGRP sends a partial routing table update, which includes just routes that have been changed.
Which statement is true regarding cisco’s RIP_JITTER variable?
It prevents the synchronization of routing updates by subtracting a random length of time ranging from 0% to 15% of the specified interval time from the next routing update interval.
What actions will occur after RouterA loses connectivity to network 114.125.16.0? (Choose two.)
RouterB will include network 123.92.76.0 and 136.125.85.0 in its update to RouterA. Router C will learn of the loss of connectivity to network 114.125.16.0 from RouterB.
Which of the following methods does split horizon use to reduce incorrect routing information?
Information learned from one source is not distributed back to that source.
The graphic shows a network that is configured to use RIP routing protocol. Router2 detects that the link to Router1 has gone down. It then advertises the network for this link with a hop count metric of 16. Which routing loop prevention mechanism is in effect?
route poisoning
What is the purpose of the TTL field in the IP header?
limits the time or hops that a packet can traverse through the network before it should be discarded
Which of the following can exist in a distance vector network that has not converged? (Choose three.)
routing loops inconsistent traffic forwarding inconsistent routing table entries
Refer to the exhibit. The routers in this network are running RIP. Router A has not received an update from Router B in over three minutes. How will Router A respond?
The Invalid timer will mark the route as unusable if an update has not been received in 180 seconds.
A network administrator is evaluating RIP versus EIGRP for a new network. The network will be sensitive to congestion and must respond quickly to topology changes. What are two good reasons to choose EIGRP instead of RIP in this case? (Choose two.)
EIGRP only updates affected neighbors. EIGRP updates are partial.
Refer to the exhibit. What path will packets from the 192.168.1.0/24 network travel to reach the 10.0.0.0/8 network if RIP is the active routing protocol?
The path will be router A -> router D -> router E.
Which three routing protocols are distance vector routing protocols? (Choose three).
RIPv1 EIGRP RIPv2
What is a routing loop?
a condition where a packet is constantly transmitted within a series of routers without ever reaching its intended destination
Which two conditions are most likely to cause a routing loop? (Choose two.)
inconsistent routing tables incorrectly configured static routes
What metric does the RIP routing protocol consider to be infinity?
16
What does a router running RIP do first with a new route that is received from an advertisement?
adjusts the metric for the new route to show the added distance for the route
Refer to the exhibit. If all routers are using RIP, how many rounds of updates will occur before all routers know all networks?
3
a route is installed in the routing table
Three routers running a distance-vector routing protocol lost all power, including the battery backups. When the routers reload, what will happen?
They will send updates that include only directly connected routes to their directly connected neighbors.
What does the RIP holddown timer do?
instructs routers to ignore updates, for a specified time or event, about possible inaccessible routes
Which two statements are true regarding the function of the RIPv1 routing updates? (Choose two).
updates are broadcast at regular intervals broadcasts are sent to 255.255.255.255
Which of the following statements are correct about RIP?
will send out an update if there is a failure of a link
Which two statements describe EIGRP? (Choose two.)
EIGRP sends triggered updates whenever there is a change in topology that influences the routing information. EIGRP sends a partial routing table update, which includes just routes that have been changed.
Which statement is true regarding cisco’s RIP_JITTER variable?
It prevents the synchronization of routing updates by subtracting a random length of time ranging from 0% to 15% of the specified interval time from the next routing update interval.
What actions will occur after RouterA loses connectivity to network 114.125.16.0? (Choose two.)
RouterB will include network 123.92.76.0 and 136.125.85.0 in its update to RouterA. Router C will learn of the loss of connectivity to network 114.125.16.0 from RouterB.
Which of the following methods does split horizon use to reduce incorrect routing information?
Information learned from one source is not distributed back to that source.
The graphic shows a network that is configured to use RIP routing protocol. Router2 detects that the link to Router1 has gone down. It then advertises the network for this link with a hop count metric of 16. Which routing loop prevention mechanism is in effect?
route poisoning
What is the purpose of the TTL field in the IP header?
limits the time or hops that a packet can traverse through the network before it should be discarded
Which of the following can exist in a distance vector network that has not converged? (Choose three.)
routing loops inconsistent traffic forwarding inconsistent routing table entries
Refer to the exhibit. The routers in this network are running RIP. Router A has not received an update from Router B in over three minutes. How will Router A respond?
The Invalid timer will mark the route as unusable if an update has not been received in 180 seconds.
A network administrator is evaluating RIP versus EIGRP for a new network. The network will be sensitive to congestion and must respond quickly to topology changes. What are two good reasons to choose EIGRP instead of RIP in this case? (Choose two.)
EIGRP only updates affected neighbors. EIGRP updates are partial.
Refer to the exhibit. What path will packets from the 192.168.1.0/24 network travel to reach the 10.0.0.0/8 network if RIP is the active routing protocol?
The path will be router A -> router D -> router E.
Which three routing protocols are distance vector routing protocols? (Choose three).
RIPv1 EIGRP RIPv2
What is a routing loop?
a condition where a packet is constantly transmitted within a series of routers without ever reaching its intended destination
Which two conditions are most likely to cause a routing loop? (Choose two.)
inconsistent routing tables incorrectly configured static routes
What metric does the RIP routing protocol consider to be infinity?
16
What does a router running RIP do first with a new route that is received from an advertisement?
adjusts the metric for the new route to show the added distance for the route
Refer to the exhibit. If all routers are using RIP, how many rounds of updates will occur before all routers know all networks?
3
CCNA 2 Chapter 3
Which two statements correctly describe the concepts of administrative distance and metric? (Choose two.)
Administrative distance refers to the trustworthiness of a particular route.
Routes with the smallest metric to a destination indicate the best path.
Refer to the exhibit. Which statement correctly describes how R1 will determine the best path to R2?
R1 will install an EIGRP route using network B in its routing table because the administrative distance of EIGRP is lower than RIP.
Which two statements are true regarding classless routing protocols? (Choose two.)
sends subnet mask information in routing updates
allows for use of both 192.168.1.0/30 and 192.168.1.16/28 subnets in the same topology
Which command would the network administrator issue to determine if load balancing is in effect on a router?
show ip route
Which statement is true regarding routing protocols?
EIGRP uses DUAL to calculate the shortest path and can be configured to do unequal cost load balancing.
Which two conditions would create a setting where the use of a distance-vector routing protocol would be efficient? (Choose two.)
the network is using a hub and spoke topology
the network is using a flat design
What is the purpose of a routing protocol?
It allows a router to share information about known networks with other routers.
Which of the following best describes the operation of distance vector routing protocols?
They send their routing tables to directly connected neighbors.
Which of the following is associated with link-state routing protocols?
shortest-path first calculations
Why is fast convergence desirable in networks that use dynamic routing protocols?
Routers may make incorrect forwarding decisions until the network has converged.
Which of the following conditions must be met in order for a network to have converged
The routers in the network are operating with consistent routing knowledge.
Which two statements are true regarding metrics? (Choose two.)
EIGRP uses bandwidth as a metric.
OSPF uses cost based on bandwidth as a metric.
Which two statements are true regarding the advantages of the use of static routes? (Choose two).
increased security
the administrator maintains control over routing
The following line of code is displayed in a routing table:
R 209.165.201.0/24 [120/2] via 192.168.252.2, 00:00:16, S0/0/0
What can be concluded from this output?
The value, 120, is used to determine the best path when a router has more than one routing protocol configured for the same destination network.
What will be the result of the following commands?
ORL(config)# interface fastethernet 0/0
ORL(config-if)# ip address 172.16.3.1 255.255.255.0
ORL(config-if)# no shutdown
A routing table entry is made to the 172.16.3.0 network with a code of "C".
An engineer creates a static route by entering the Router(config)# ip route 10.0.0.0 255.255.255.0 192.168.1.2 command. What can be concluded about this route?
The administrative distance of this route is 1.
Refer to the exhibit. Router1 and Router2 are running EIGRP. All interfaces are operational and packets can be forwarded between all networks. What information will be found in the routing table for Router1?
The administrative distance of the route to network 172.16.0.0 will be 90.
The following line of code is present in the routing table:
O 10.16.1.0/27 [110/129] via 192.168.1.5, 00:00:05, Serial0/0/1
What does the number 129 indicate in this output?
The cost for this link has a value of 129.
A growing medium-sized manufacturing company recently began to have routing instability issues. The company uses static routes and has a mixture of over 30 Cisco and non-Cisco routers. The network administrator has decided to convert the network to dynamic routing. What characteristics of protocols should be considered in this selection process?
OSPF can be used between the routers.
Refer to the exhibit. If RIP is the routing protocol, what is the value of the metric from router A to network 192.168.5.0/24?
3
A router learns two paths with equal metrics to a destination network via the RIP routing protocol. How will the router handle packets to the destination network?
The router will install both routes in the routing table and load balance between the two.
Administrative distance refers to the trustworthiness of a particular route.
Routes with the smallest metric to a destination indicate the best path.
Refer to the exhibit. Which statement correctly describes how R1 will determine the best path to R2?
R1 will install an EIGRP route using network B in its routing table because the administrative distance of EIGRP is lower than RIP.
Which two statements are true regarding classless routing protocols? (Choose two.)
sends subnet mask information in routing updates
allows for use of both 192.168.1.0/30 and 192.168.1.16/28 subnets in the same topology
Which command would the network administrator issue to determine if load balancing is in effect on a router?
show ip route
Which statement is true regarding routing protocols?
EIGRP uses DUAL to calculate the shortest path and can be configured to do unequal cost load balancing.
Which two conditions would create a setting where the use of a distance-vector routing protocol would be efficient? (Choose two.)
the network is using a hub and spoke topology
the network is using a flat design
What is the purpose of a routing protocol?
It allows a router to share information about known networks with other routers.
Which of the following best describes the operation of distance vector routing protocols?
They send their routing tables to directly connected neighbors.
Which of the following is associated with link-state routing protocols?
shortest-path first calculations
Why is fast convergence desirable in networks that use dynamic routing protocols?
Routers may make incorrect forwarding decisions until the network has converged.
Which of the following conditions must be met in order for a network to have converged
The routers in the network are operating with consistent routing knowledge.
Which two statements are true regarding metrics? (Choose two.)
EIGRP uses bandwidth as a metric.
OSPF uses cost based on bandwidth as a metric.
Which two statements are true regarding the advantages of the use of static routes? (Choose two).
increased security
the administrator maintains control over routing
The following line of code is displayed in a routing table:
R 209.165.201.0/24 [120/2] via 192.168.252.2, 00:00:16, S0/0/0
What can be concluded from this output?
The value, 120, is used to determine the best path when a router has more than one routing protocol configured for the same destination network.
What will be the result of the following commands?
ORL(config)# interface fastethernet 0/0
ORL(config-if)# ip address 172.16.3.1 255.255.255.0
ORL(config-if)# no shutdown
A routing table entry is made to the 172.16.3.0 network with a code of "C".
An engineer creates a static route by entering the Router(config)# ip route 10.0.0.0 255.255.255.0 192.168.1.2 command. What can be concluded about this route?
The administrative distance of this route is 1.
Refer to the exhibit. Router1 and Router2 are running EIGRP. All interfaces are operational and packets can be forwarded between all networks. What information will be found in the routing table for Router1?
The administrative distance of the route to network 172.16.0.0 will be 90.
The following line of code is present in the routing table:
O 10.16.1.0/27 [110/129] via 192.168.1.5, 00:00:05, Serial0/0/1
What does the number 129 indicate in this output?
The cost for this link has a value of 129.
A growing medium-sized manufacturing company recently began to have routing instability issues. The company uses static routes and has a mixture of over 30 Cisco and non-Cisco routers. The network administrator has decided to convert the network to dynamic routing. What characteristics of protocols should be considered in this selection process?
OSPF can be used between the routers.
Refer to the exhibit. If RIP is the routing protocol, what is the value of the metric from router A to network 192.168.5.0/24?
3
A router learns two paths with equal metrics to a destination network via the RIP routing protocol. How will the router handle packets to the destination network?
The router will install both routes in the routing table and load balance between the two.
CCNA 2 Chapter 2
Which of the following are displayed by the Router# show cdp neighbors command? (Choose three.)
platform
holdtime
local interface
Why is it advisable to enter a next-hop IP address when creating a static route whose exit interface is an Ethernet network?
In a multi-access network, the router cannot determine the next-hop MAC address for the Ethernet frame without a next-hop address.
The output of the Router# show interfaces serial 0/1 command displays the following:
Serial0/1 is up, line protocol is down.
What is the most likely cause for the line protocol being down?
No clock rate has been set.
A static route that points to the next hop IP will have what administrative distance and metric in the routing table?
administrative distance of 1 and metric of 0
Refer to the exhibit. What two commands will change the next-hop address for the 10.0.0.0/8 network from 172.16.40.2 to 192.168.1.2? (Choose two.)
A(config)# no ip route 10.0.0.0 255.0.0.0 172.16.40.2
A(config)# ip route 10.0.0.0 255.0.0.0 192.168.1.2
Refer to the exhibit. A company network engineer is assigned to establish connectivity between the two Ethernet networks so that hosts on the 10.1.1.0/24 subnet can contact hosts on the 10.1.2.0/24 subnet. The engineer has been told to use only static routing for these company routers. Which set of commands will establish connectivity between the two Ethernet networks?
R1(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.2R2(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.1
Refer to the exhibit. Which static route should be configured on Router1 so that host A will be able to reach host B on the 172.16.0.0 network?
ip route 172.16.0.0 255.255.0.0 S0/0/0
What address can be used to summarize networks 172.16.1.0/24, 172.16.2.0/24, 172.16.3.0/24, and 172.16.4.0/24?
172.16.0.0/21
Refer to the exhibit. What is the significance of the /8 in the route to the 10.0.0.0 network?
It indicates the number of consecutive bits, from the left, in the destination IP address of a packet that must match 10.0.0.0 to use that route.
What two devices are responsible for converting the data from the WAN service provider into a form acceptable by the router? (Choose two).
a modem
a CSU/DSU device
A network administrator enters the following command into Router1: ip route 192.168.0.0 255.255.255.0 S0/1/0. Router1 then receives a packet that is destined for 192.168.0.22/24. After finding the recently configured static route in the routing table, what does Router1 do next to process the packet?
encapsulates the packet into a frame for the WAN link and forwards the packet out the S0/1/0 interface
Which piece of information is available from examining the output of the command show ip interface brief?
Interface IP address
Which of the following is true regarding CDP and the graphic shown?
By default, Router A will receive CDP advertisements from routers B and C.
Which two statements describe functions or characteristics of CDP? (Choose two.)
It starts up automatically and allows the device to detect directly connected neighbor devices that use CDP.
It allows systems to learn about each other even if different network layer protocols are configured.
Hosts on two separate subnets cannot communicate. The network administrator suspects a missing route in one of the routing tables. Which three commands can be used to help troubleshoot Layer 3 connectivity issues? (Choose three.)
ping
traceroute
show ip route
What happens to a static route entry in a routing table when the outgoing interface is not available?
The route is removed from the table.
The routers in the diagram use the subnet assignments shown. What is the most efficient route summary that can be configured on Router3 to advertise the internal networks to the cloud?
192.1.1.0/25
Refer to the exhibit. How will packets destined to the 172.16.0.0 network be forwarded?
Router1 will perform recursive lookup and packet will exit S0/0.
A router has one static route to each destination network. Which two scenarios would require an administrator to alter the static routes that are configured on that router? (Choose two.)
The destination network no longer exists.
A topology change occurs where the existing next-hop address or exit interface is not accessible.
Refer to the exhibit. Given the output in the exhibit, how would a clock rate be determined for this link?
The rate configured on the DCE determines the clock rate.
Refer to the exhibit. Which set of commands will configure static routes that will allow the WinterPark and the Altamonte routers to deliver packets from each LAN and direct all other traffic to the Internet?
WinterPark(config)# ip route 0.0.0.0 0.0.0.0 192.168.146.1Altamonte(config)# ip route 10.0.234.0 255.255.255.0 192.168.146.2Altamonte(config)# ip route 0.0.0.0 0.0.0.0 s0/1
Refer to the exhibit. What two commands are required to provide connectivity between the 192.168.1.0 and 10.0.0.0 networks without requiring recursive lookup? (Choose two.)
A(config)# ip route 10.0.0.0 255.0.0.0 s 0/1/0
B(config)# ip route 192.168.1.0 255.255.255.0 s 0/0/0
platform
holdtime
local interface
Why is it advisable to enter a next-hop IP address when creating a static route whose exit interface is an Ethernet network?
In a multi-access network, the router cannot determine the next-hop MAC address for the Ethernet frame without a next-hop address.
The output of the Router# show interfaces serial 0/1 command displays the following:
Serial0/1 is up, line protocol is down.
What is the most likely cause for the line protocol being down?
No clock rate has been set.
A static route that points to the next hop IP will have what administrative distance and metric in the routing table?
administrative distance of 1 and metric of 0
Refer to the exhibit. What two commands will change the next-hop address for the 10.0.0.0/8 network from 172.16.40.2 to 192.168.1.2? (Choose two.)
A(config)# no ip route 10.0.0.0 255.0.0.0 172.16.40.2
A(config)# ip route 10.0.0.0 255.0.0.0 192.168.1.2
Refer to the exhibit. A company network engineer is assigned to establish connectivity between the two Ethernet networks so that hosts on the 10.1.1.0/24 subnet can contact hosts on the 10.1.2.0/24 subnet. The engineer has been told to use only static routing for these company routers. Which set of commands will establish connectivity between the two Ethernet networks?
R1(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.2R2(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.1
Refer to the exhibit. Which static route should be configured on Router1 so that host A will be able to reach host B on the 172.16.0.0 network?
ip route 172.16.0.0 255.255.0.0 S0/0/0
What address can be used to summarize networks 172.16.1.0/24, 172.16.2.0/24, 172.16.3.0/24, and 172.16.4.0/24?
172.16.0.0/21
Refer to the exhibit. What is the significance of the /8 in the route to the 10.0.0.0 network?
It indicates the number of consecutive bits, from the left, in the destination IP address of a packet that must match 10.0.0.0 to use that route.
What two devices are responsible for converting the data from the WAN service provider into a form acceptable by the router? (Choose two).
a modem
a CSU/DSU device
A network administrator enters the following command into Router1: ip route 192.168.0.0 255.255.255.0 S0/1/0. Router1 then receives a packet that is destined for 192.168.0.22/24. After finding the recently configured static route in the routing table, what does Router1 do next to process the packet?
encapsulates the packet into a frame for the WAN link and forwards the packet out the S0/1/0 interface
Which piece of information is available from examining the output of the command show ip interface brief?
Interface IP address
Which of the following is true regarding CDP and the graphic shown?
By default, Router A will receive CDP advertisements from routers B and C.
Which two statements describe functions or characteristics of CDP? (Choose two.)
It starts up automatically and allows the device to detect directly connected neighbor devices that use CDP.
It allows systems to learn about each other even if different network layer protocols are configured.
Hosts on two separate subnets cannot communicate. The network administrator suspects a missing route in one of the routing tables. Which three commands can be used to help troubleshoot Layer 3 connectivity issues? (Choose three.)
ping
traceroute
show ip route
What happens to a static route entry in a routing table when the outgoing interface is not available?
The route is removed from the table.
The routers in the diagram use the subnet assignments shown. What is the most efficient route summary that can be configured on Router3 to advertise the internal networks to the cloud?
192.1.1.0/25
Refer to the exhibit. How will packets destined to the 172.16.0.0 network be forwarded?
Router1 will perform recursive lookup and packet will exit S0/0.
A router has one static route to each destination network. Which two scenarios would require an administrator to alter the static routes that are configured on that router? (Choose two.)
The destination network no longer exists.
A topology change occurs where the existing next-hop address or exit interface is not accessible.
Refer to the exhibit. Given the output in the exhibit, how would a clock rate be determined for this link?
The rate configured on the DCE determines the clock rate.
Refer to the exhibit. Which set of commands will configure static routes that will allow the WinterPark and the Altamonte routers to deliver packets from each LAN and direct all other traffic to the Internet?
WinterPark(config)# ip route 0.0.0.0 0.0.0.0 192.168.146.1Altamonte(config)# ip route 10.0.234.0 255.255.255.0 192.168.146.2Altamonte(config)# ip route 0.0.0.0 0.0.0.0 s0/1
Refer to the exhibit. What two commands are required to provide connectivity between the 192.168.1.0 and 10.0.0.0 networks without requiring recursive lookup? (Choose two.)
A(config)# ip route 10.0.0.0 255.0.0.0 s 0/1/0
B(config)# ip route 192.168.1.0 255.255.255.0 s 0/0/0
CCNA 2 Chapter 1
If a router cannot find a valid configuration file during the startup sequence, what will occur?
The router will prompt the user for a response to enter setup mode.
Refer to the exhibit. The network administrator has configured the router with the interface IP addresses shown for the directly connected networks. Pings from the router to hosts on the connected networks or pings between router interfaces are not working. What is the most likely problem?
The interfaces must be enabled with the no shutdown command.
Refer to the exhibit. What can be concluded from the routing table output in the exhibit? (Choose two.)
The FastEthernet0/0 and Serial0/0/0 interfaces of this router were configured with an IP address and the no shutdown command.
An IP packet received by this router with a destination address of 198.18.9.1 will be forwarded out of the Serial0/0/0 interface.
Refer to the exhibit. The frame shown in the exhibit was received by the router. The router interfaces are operational. How will the router process this frame? (Choose two.)
The router will change the frame type to one supported by the WAN link before forwarding the frame.
The frame was received on the Fa0/0 interface of the router and will be switched to the S0/0/0 interface.
Passwords can be used to restrict access to all or parts of the Cisco IOS. Select the modes and interfaces that can be protected with passwords. (Choose three.)
VTY interface
console interface
privileged EXEC mode
Which two statements correctly describe the components of a router? (Choose two.)
ROM contains diagnostics executed on hardware modules.
Flash memory does not lose its contents during a reboot.
Refer to the exhibit. After host 2 is connected to the switch on the LAN, host 2 is unable to communicate with host 1. What is the cause of this problem?
The subnet mask of host 2 is incorrect.
Host 1 and host 2 are on different networks.
The switch needs an IP address that is not configured.
The router LAN interface and host 1 are on different networks.
The IP address of host 1 is on a different network than is the LAN interface of the router.
Which are functions of a router? (Choose three.)
packet switching
segmentation of broadcast domains
selection of best path based on logical addressing
Refer to the exhibit. All routers have a route in its routing table to each network that is shown in the exhibit. Default routes have not been issued on these routers. What can be concluded about how packets are forwarded in this network? (Choose two.)
If RouterA receives a packet that is destined for 192.168.3.146, it will be forwarded out interface S0/0/1.
If RouterB receives a packet that is destined for 10.5.27.15, it will be forwarded out interface S0/0/1.
The serial connection shown in the graphic needs to be configured. Which configuration commands must be made on the Sydney router to establish connectivity with the Melbourne site? (Choose three.)
Sydney(config-if)# ip address 201.100.53.2 255.255.255.0
Sydney(config-if)# no shutdown
Sydney(config-if)# clock rate 56000
Refer to the exhibit. What can be concluded from the output of the running-configuration of a router?
The commands that are displayed determine the current operation of the router.
Refer to the exhibit. Host A pings host B. When R4 accepts the ping into the Ethernet interface, what two pieces of header information are included? (Choose two.)
destination IP address: 192.168.10.134
destination MAC address: 9999.DADC.1234
What is the outcome of entering these commands?
R1(config)# line vty 0 4
R1(config-line)# password check123
R1(config-line)# login
sets the password to be used for connecting to this router via Telnet
Which of the following is the correct flow of routines for a router startup?
load bootstrap, load IOS, apply configuration
What three processes does a router execute when it receives a packet from one network that is destined for another network? (Choose three.)
decapsulates the Layer 3 packet by stripping off the Layer 2 frame header
uses the destination IP Address in the IP header to look up the next-hop address in the routing table
encapsulates the Layer 3 packet into the new Layer 2 frame and forwards it out the exit interface
The network administrator needs to connect two routers directly via their FastEthernet ports. What cable should the network administrator use?
cross-over
Which two statements describe characteristics of load balancing? (Choose two.)
Load balancing allows a router to forward packets over multiple paths to the same destination network.
Unequal cost load balancing is supported by EIGRP.
What information about the router and its startup process can be gathered from the output of the show version command? (Choose three.)
the last restart method
the configuration register settings
the location from where the IOS loaded
Which interfaces in the exhibit could be used for a leased line WAN connection? (Choose two.)
1
4
From what location can a router load the Cisco IOS during the boot process? (Choose two.)
TFTP server
Flash memory
A network administrator has just entered new configurations into Router1. Which command should be executed to save configuration changes to NVRAM?
Router1# copy running-config startup-config
What is the default sequence for loading the configuration file?
NVRAM, TFTP, CONSOLE
What header address information does a router change in the information it receives from an attached Ethernet interface before information is transmitted out another interface?
the Layer 2 source and destination address
The router will prompt the user for a response to enter setup mode.
Refer to the exhibit. The network administrator has configured the router with the interface IP addresses shown for the directly connected networks. Pings from the router to hosts on the connected networks or pings between router interfaces are not working. What is the most likely problem?
The interfaces must be enabled with the no shutdown command.
Refer to the exhibit. What can be concluded from the routing table output in the exhibit? (Choose two.)
The FastEthernet0/0 and Serial0/0/0 interfaces of this router were configured with an IP address and the no shutdown command.
An IP packet received by this router with a destination address of 198.18.9.1 will be forwarded out of the Serial0/0/0 interface.
Refer to the exhibit. The frame shown in the exhibit was received by the router. The router interfaces are operational. How will the router process this frame? (Choose two.)
The router will change the frame type to one supported by the WAN link before forwarding the frame.
The frame was received on the Fa0/0 interface of the router and will be switched to the S0/0/0 interface.
Passwords can be used to restrict access to all or parts of the Cisco IOS. Select the modes and interfaces that can be protected with passwords. (Choose three.)
VTY interface
console interface
privileged EXEC mode
Which two statements correctly describe the components of a router? (Choose two.)
ROM contains diagnostics executed on hardware modules.
Flash memory does not lose its contents during a reboot.
Refer to the exhibit. After host 2 is connected to the switch on the LAN, host 2 is unable to communicate with host 1. What is the cause of this problem?
The subnet mask of host 2 is incorrect.
Host 1 and host 2 are on different networks.
The switch needs an IP address that is not configured.
The router LAN interface and host 1 are on different networks.
The IP address of host 1 is on a different network than is the LAN interface of the router.
Which are functions of a router? (Choose three.)
packet switching
segmentation of broadcast domains
selection of best path based on logical addressing
Refer to the exhibit. All routers have a route in its routing table to each network that is shown in the exhibit. Default routes have not been issued on these routers. What can be concluded about how packets are forwarded in this network? (Choose two.)
If RouterA receives a packet that is destined for 192.168.3.146, it will be forwarded out interface S0/0/1.
If RouterB receives a packet that is destined for 10.5.27.15, it will be forwarded out interface S0/0/1.
The serial connection shown in the graphic needs to be configured. Which configuration commands must be made on the Sydney router to establish connectivity with the Melbourne site? (Choose three.)
Sydney(config-if)# ip address 201.100.53.2 255.255.255.0
Sydney(config-if)# no shutdown
Sydney(config-if)# clock rate 56000
Refer to the exhibit. What can be concluded from the output of the running-configuration of a router?
The commands that are displayed determine the current operation of the router.
Refer to the exhibit. Host A pings host B. When R4 accepts the ping into the Ethernet interface, what two pieces of header information are included? (Choose two.)
destination IP address: 192.168.10.134
destination MAC address: 9999.DADC.1234
What is the outcome of entering these commands?
R1(config)# line vty 0 4
R1(config-line)# password check123
R1(config-line)# login
sets the password to be used for connecting to this router via Telnet
Which of the following is the correct flow of routines for a router startup?
load bootstrap, load IOS, apply configuration
What three processes does a router execute when it receives a packet from one network that is destined for another network? (Choose three.)
decapsulates the Layer 3 packet by stripping off the Layer 2 frame header
uses the destination IP Address in the IP header to look up the next-hop address in the routing table
encapsulates the Layer 3 packet into the new Layer 2 frame and forwards it out the exit interface
The network administrator needs to connect two routers directly via their FastEthernet ports. What cable should the network administrator use?
cross-over
Which two statements describe characteristics of load balancing? (Choose two.)
Load balancing allows a router to forward packets over multiple paths to the same destination network.
Unequal cost load balancing is supported by EIGRP.
What information about the router and its startup process can be gathered from the output of the show version command? (Choose three.)
the last restart method
the configuration register settings
the location from where the IOS loaded
Which interfaces in the exhibit could be used for a leased line WAN connection? (Choose two.)
1
4
From what location can a router load the Cisco IOS during the boot process? (Choose two.)
TFTP server
Flash memory
A network administrator has just entered new configurations into Router1. Which command should be executed to save configuration changes to NVRAM?
Router1# copy running-config startup-config
What is the default sequence for loading the configuration file?
NVRAM, TFTP, CONSOLE
What header address information does a router change in the information it receives from an attached Ethernet interface before information is transmitted out another interface?
the Layer 2 source and destination address
CCNA 1 Final
1. Refer to the exhibit. Host B attempts to establish a TCP/IP session with host C. During this attempt, a frame was captured at the FastEthernet interface fa0/1 of the San Francisco router. The packet inside the captured frame has the source IP address 10.10.1.2, and the destination IP address is 10.31.1.20. What is the destination MAC address of the frame at the time of capture?
• 0060.7320.D632
• 0060.7320.D631
• 0040.8517.44C3
• 0009.B2E4.EE03
• 0010.C2B4.3421
2. What are three characteristics of CSMA/CD? (Choose three.)
• It monitors the media for presence of a data signal.
• After detecting a collision, hosts can resume transmission after a random timer has expired.
• A jam signal is used to ensure that all hosts are aware that a collision has occurred.
• Devices can be configured with a higher transmission priority.
• Data is transmitted only when the data signal is present.
• It uses a token system to avoid collisions.
3. Refer to the exhibit. The PC, the routing table of which is displayed, is configured correctly. To which network device or interface does the IP address 192.168.1.254 belong?
• PC
• switch
• router interface fa0/0
• router interface fa0/1
4. Refer to the exhibit. Host A wants to access the Internet. Which combination of a Layer 2 address and a Layer 3 address will enable this access from host A?
• Destination MAC: 0030.8596.DE83 Default gateway: 209.165.202.130
• Destination MAC: 0030.8596.DE82 Default gateway: 172.16.9.2
• Destination MAC: 0030.8517.44C4 Default gateway: 172.16.1.1
• Destination MAC: 0030.8517.44C4 Default gateway: 209.165.202.130
5. Refer to the exhibit. Communication between hosts X and Y is restricted to the local network. What is the reason for this?
• The gateway addresses are broadcast addresses.
• Host Y is assigned a multicast address.
• Host X and host Y belong to different networks.
• Host X is assigned a network address.
6. What is the result of using the clock rate 56000 command at the serial interface of the router?
• The interface is configured as a DCE device.
• The interface timers are cleared.
• The FastEthernet interface is made to emulate a serial interface by assigning it a timing signal.
• The IP address for the serial interface is configured.
7. Which three addresses belong to the category of public IP addresses? (Choose three.)
• 127.0.0.1
• 196.1.105.6
• 132.11.9.99
• 10.0.0.1
• 172.16.9.10
• 46.1.1.97
8. Which three statements are true about transport layer protocols? (Choose three.)
• TCP and UDP manage communication between multiple applications.
• TCP retransmits the packets for which the acknowledgment is not received.
• TCP acknowledges received data.
• UDP exchanges frames between the nodes of the network.
• TCP has no mechanism to acknowledge transmission errors.
• UDP uses windowing and sequencing to provide reliable transfer of data.
9. Refer to the exhibit. Which logical topology describes the exhibited network?
• star
• ring
• point-to-point
• multi-access
10. Which statement is true about the running configuration file in a Cisco IOS device?
• It affects the operation of the device immediately when modified.
• It is stored in NVRAM.
• It should be deleted using the erase running-config command.
• It is automatically saved when the router reboots.
11. Refer to the exhibit. Host C is able to ping 127.0.0.1 successfully, but is unable to communicate with hosts A and B in the organization. What is the likely cause of the problem?
• Hosts A and B are not on the same subnet as host C.
• The IP addresses on the router serial interfaces are wrong.
• The subnet mask on host C is improperly configured.
• The FastEthernet interface fa0/0 of router 1 is wrongly configured.
12. A host is transmitting a video over the network. How does the transport layer allow this host to use multiple applications to transmit other data at the same time as the video transmission?
• It uses error control mechanisms.
• It uses a connectionless protocol only for multiple simultaneous transmissions.
• It uses multiple Layer 2 source addresses.
• It uses multiple port numbers.
13. Refer to the exhibit. PC1 is unable to access PC2. To troubleshoot this problem, the technician needs to confirm that the next hop interface is operational. Which default gateway address should the technician ping from PC1 to confirm this?
• 10.0.0.254
• 192.168.0.249
• 192.168.0.250
• 10.0.1.254
14. Refer to the exhibit. Cable 1 and Cable 2 are wired for specific physical layer requirements. Which three segments use Cable 2? (Choose three.)
• Segment 1
• Segment 2
• Segment 3
• Segment 4
• Segment 5
• Segment 6
15. Refer to the exhibit. Which two facts can be determined about the topology? (Choose two.)
• Three networks are needed.
• Two logical address ranges are required.
• A single broadcast domain is present.
• Three collision domains are present.
• Four networks are needed.
16. Refer to the exhibit. Which three statements are true about the IP configuration that is displayed? (Choose three.)
• The assigned address is a private address.
• The PC cannot communicate with the DNS server.
• The network can have 126 hosts.
• The prefix of the computer address is /26.
• The IP address is routable on the Internet.
• The IP address is a multicast address. 17. Which password restricts Telnet access to the router?
• enable
• enable secret
• console
• VTY
18. Refer to the exhibit. To create the initial configuration, a network technician connected host A to the router using the connection that is shown. Which statement is true about this connection?
• It terminates at the Ethernet port of the router.
• It provides out-of-band console access.
• It terminates at the serial interface of the router.
• It requires a Telnet client on host A to access the router. 19. Which device should be used for routing a packet to a remote network?
• access switch
• DHCP server
• hub
• router
20. Refer to the exhibit. The serial interface of the router was configured with the use of the commands that are shown. The router cannot ping the router that is directly connected to interface serial 0/0/0. What should the network technician do to solve this problem?
• Configure the description at interface serial 0/0/0.
• Configure an IP address on interface serial 0/0/0.
• Remove the no shutdown command at interface serial 0/0/0
• Reboot the router.
21. Refer to the exhibit. In a network, host A is sending data segments to host B. The flow control of the segments that are being exchanged is displayed. Which two statements are true about this communication? (Choose two.)
• The initial window size is determined via the two-way handshake.
• The window size for the TCP session that is represented is initially set to 3000 bytes.
• Acknowledgment number 3001 indicates that host A will send the next segment with sequence number 3001.
• Host B expects that the next received segment number will be 3000.
• No more acknowledgments will be exchanged.
22. Refer to the exhibit. The network administrator wants to remotely access the CLI of the router from PC1 using modem 1. Which port of the router should be connected to modem 2 to enable this access?
• console
• Ethernet
• auxiliary
• serial 23. Which OSI layer uses a connection-oriented protocol to ensure reliable delivery of data?
• application layer
• presentation layer
• session layer
• transport layer 24. What are two functions of the data link layer? (Choose two.)
• It segments and reorders the data.
• It exchanges data between programs that are running on the source and destination hosts.
• It controls how data is placed onto the media.
• It generates signals to represent the bits in each frame.
• It encapsulates each packet with a header and a trailer to transfer it across the local media. 25. Refer to the exhibit. Which list refers only to end devices?
• D,E,F,G
• A,H,B,C
• A,D,E,F
• A,D,E,G
26. Refer to the exhibit. The diagram represents the process of sending e-mail between clients. Which list correctly identifies the component or protocol used at each numbered stage of the diagram?
• 1.MUA 2.MDA 3.MTA 4.SMTP 5.MTA 6.POP 7.MDA 8.MUA
• 1.MUA 2.POP 3.MDA 4.SMTP 5.MTA 6.MDA 7.SMTP 8.MUA
• 1.MUA 2.POP 3.SMTP 4.MDA 5.MTA 6.SMTP 7.POP 8.MUA
• 1.MUA 2.SMTP 3.MTA 4.SMTP 5.MTA 6.MDA 7.POP 8.MUA
27. Refer to the exhibit. Host B was powered off. What change will occur in the MAC table of the switch?
The table will remain unaffected.
• The switch will remove the MAC address at Fa0/19 immediately.
• The switch will retain the MAC address until host B is powered on again.
• The switch will rebuild the MAC table by assigning the FFFF.FFFF.FFFF address to port Fa0/19.
28. Refer to the exhibit. A technician has connected the PC to the switch using a Category 6 UTP cable. Which two statements are true about this connection? (Choose two.)
• The cable that is used is an Ethernet crossover cable.
• The transmit pin of the cable is terminated to the receive pin.
• The maximum distance between the switch and the PC can be 100 m.
• The maximum supported bandwidth is 1000 Mb/s.
• The Category 6 cable simulates a point-to-point WAN link and is unusable for this type of connection.
29. Refer to the exhibit. A host is using NAT to connect to the Internet. Which three IP addresses enable this connection? (Choose three.)
• 10.1.1.63
• 10.1.1.37
• 10.1.1.39
• 10.1.1.32
• 10.1.1.60
• 10.1.1.2 30. Refer to the exhibit. A PC is communicating with another PC on a remote network. The two networks are connected by three routers. Which action will help to identify the path between the hosts?
• Use the ipconfig command at the host.
• Use the ipconfig/all command at the destination.
• Use the tracert command at the host.
• Use the ping command at the destination.
31. An organization wants to create a subnet of the IP network 172.16.0.0. This subnet will accommodate 1000 hosts. Which subnet mask should be assigned to this network?
• 255.255.0.0
• 255.255.248.0
• 255.255.252.0
• 255.255.254.0
• 255.255.255.0
• 255.255.255.128
32. Refer to the exhibit. A host is connected to hub 1. Which combination of IP address, subnet mask, and default gateway can allow this host to function in the network?
• IP address: 172.16.31.36 Subnet mask: 255.255.255.240 Default gateway: 172.16.31.35
• IP address: 172.16.31.63 Subnet mask: 255.255.255.224 Default gateway: 172.16.31.35
IP address: 172.16.31.29 Subnet mask: 255.255.255.248 Default gateway: 172.16.31.35
• IP address: 172.16.31.32 Subnet mask: 255.255.255.224 Default gateway: 172.16.31.35
• IP address: 172.16.31.29 Subnet mask: 255.255.255.240 Default gateway: 172.16.30.1
• IP address: 172.16.31.37 Subnet mask: 255.255.255.224 Default gateway: 172.16.31.35
33. Refer to the exhibit. A technician uses the nslookup command on the PC and views the output that is displayed in the exhibit. What is the IP address of the primary domain name server configured at the host? (Choose two.)
• 192.168.1.99
• 192.168.2.100
• 10.10.10.32
• 192.168.1.5
• the IP address of the website resolver1.xyz.local
34. Which OSI layer offers ordered data reconstruction services?
• application layer
• network layer
• presentation layer
• session layer
• transport layer
35. Refer to the exhibit. All devices in the network use default configurations. How many logical address ranges are required in this topology?
• 2
• 3
• 4
• 5
• 6
36. The network administrator wants to install a private application on a server. Which range of port numbers is normally assigned to this application to make it accessible by clients?
• 0 to 255
• 49152 to 65535
• 1024 to 49151
• 0 to 1023
37. Because of a security violation, the router password must be changed. What information can be learned from these configuration entries? (Choose two.)
• Router(config)# line vty 0 4
Router(config-line)# password arj15
Router(config-line)# login
• This configuration allows users to connect by using a modem.
• Users must specify which line, 0 or 4, they wish to connect to when making a connection.
• This configuration allows users to connect to the router via the use of the telnet command.
• This configuration allows five users to make simultaneous connections to this router.
• The configured password is automatically encrypted on the router.
38. Refer to the exhibit. Each media link is labeled. What type of cable should be used to connect the different devices?
• Connection 1 - rollover cable Connection 2 - straight-through cable Connection 3 - crossover cable
• Connection 1 - straight-through cable Connection 2 - crossover cable Connection 3 - rollover cable
• Connection 1 - crossover cable Connection 2 - rollover cable Connection 3 - straight-through cable
• Connection 1 - crossover cable Connection 2 - straight-through cable Connection 3 - rollover cable
• Connection 1 - straight-through cable Connection 2 - straight-through cable Connection 3 - straight-through cable
39. Which two types of media are useful for connecting two devices separated by a distance of 500 meters? (Choose two.)
• 10 BASE-T
• 1000 BASE-TX
• 10 BASE-2
• 1000 BASE LX
• 1000 BASE-SX 40. Which information is used by the router to determine the path between the source and destination hosts?
• the host portion of the IP address
• the network portion of the IP address
• host default gateway address
• the MAC address
41. Refer to the exhibit. What two facts can be determined from the session information that is displayed? (Choose two.)
• This exchange is part of the three-way handshake.
• The destination port indicates that a Telnet session has been initiated.
• The source port does not support communication with the destination port that is listed.
• The destination port indicates that an SMTP session has been initiated.
• The protocol is a connection-oriented protocol.
42. Refer to the exhibit. Host A is accessing multiple servers. Which combination of port number and address will uniquely identify a particular process running on a specific server?
• MAC address of the server and port number of the service
• IP address of the host and port number of the service
• MAC address of the host and port number of the service
• IP address of the server and port number of the service
43. A network technician wants to configure an IP address on a router interface by using the ip address 192.168.1.0 255.255.255.0 command. Which prompt should the technician see when entering this command?
• Router>
• Router(config-if)#
• Router#
• Router(config)# 44. Refer to the exhibit. Host X is unable to communicate with host Y. Which command can be run at host X to determine which intermediary device is responsible for this failure?
• telnet 192.168.1.1
• ping 192.168.1.1
• ftp 192.168.1.1
• tracert 192.168.1.1
45. Refer to the exhibit. In a network, PC1 sends a message to PC2. The frame received at PC2 is shown. What information in this frame determines the correct destination application?
• timing and synchronization bits
• destination and source physical addresses
• destination and source logical network addresses
• destination and source process numbers
46. An organization has been assigned network ID 10.10.128.0 and subnet mask 255.255.224.0. Which IP address range can be used for this organization?
• 10.10.128.0 to 10.10.160.255
• 10.10.128.0 to 10.10.159.255
• 10.10.128.0 to 10.10.192.255
• 10.10.128.0 to 10.10.0.159
• 10.10.128.0 to 10.10.159.0
47. What is the effect of using the Router# copy running-config startup-config command on a router?
• The contents of ROM will change.
• The contents of RAM will change.
• The contents of NVRAM will change.
• The contents of flash will change.
48. Which three IPv4 addresses represent valid host addresses for a subnet? (Choose three.)
• 10.1.12.79/28
• 10.1.12.113/28
• 10.1.12.32/28
• 10.1.11.5/27
• 10.1.11.97/27
• 10.1.11.128/27
49. Refer to the exhibit. The NAT functionality of the router is enabled to provide Internet access to the PC. However, the PC is still unable to access the Internet. Which IP address should be changed to 209.165.201.1 to enable the PC to access the Internet?
• 192.168.1.191
• 192.168.1.101
• 192.168.1.1
• 192.168.1.254
50. Which three statements are true about network layer addressing? (Choose three.)
• It uniquely identifies each host.
• It assists in forwarding packets across internetworks.
• It uses a logical 32-bit IPv4 address.
• It is not a configurable address.
• It is a physical address.
• It identifies the host from the first part of the address.
• 0060.7320.D632
• 0060.7320.D631
• 0040.8517.44C3
• 0009.B2E4.EE03
• 0010.C2B4.3421
2. What are three characteristics of CSMA/CD? (Choose three.)
• It monitors the media for presence of a data signal.
• After detecting a collision, hosts can resume transmission after a random timer has expired.
• A jam signal is used to ensure that all hosts are aware that a collision has occurred.
• Devices can be configured with a higher transmission priority.
• Data is transmitted only when the data signal is present.
• It uses a token system to avoid collisions.
3. Refer to the exhibit. The PC, the routing table of which is displayed, is configured correctly. To which network device or interface does the IP address 192.168.1.254 belong?
• PC
• switch
• router interface fa0/0
• router interface fa0/1
4. Refer to the exhibit. Host A wants to access the Internet. Which combination of a Layer 2 address and a Layer 3 address will enable this access from host A?
• Destination MAC: 0030.8596.DE83 Default gateway: 209.165.202.130
• Destination MAC: 0030.8596.DE82 Default gateway: 172.16.9.2
• Destination MAC: 0030.8517.44C4 Default gateway: 172.16.1.1
• Destination MAC: 0030.8517.44C4 Default gateway: 209.165.202.130
5. Refer to the exhibit. Communication between hosts X and Y is restricted to the local network. What is the reason for this?
• The gateway addresses are broadcast addresses.
• Host Y is assigned a multicast address.
• Host X and host Y belong to different networks.
• Host X is assigned a network address.
6. What is the result of using the clock rate 56000 command at the serial interface of the router?
• The interface is configured as a DCE device.
• The interface timers are cleared.
• The FastEthernet interface is made to emulate a serial interface by assigning it a timing signal.
• The IP address for the serial interface is configured.
7. Which three addresses belong to the category of public IP addresses? (Choose three.)
• 127.0.0.1
• 196.1.105.6
• 132.11.9.99
• 10.0.0.1
• 172.16.9.10
• 46.1.1.97
8. Which three statements are true about transport layer protocols? (Choose three.)
• TCP and UDP manage communication between multiple applications.
• TCP retransmits the packets for which the acknowledgment is not received.
• TCP acknowledges received data.
• UDP exchanges frames between the nodes of the network.
• TCP has no mechanism to acknowledge transmission errors.
• UDP uses windowing and sequencing to provide reliable transfer of data.
9. Refer to the exhibit. Which logical topology describes the exhibited network?
• star
• ring
• point-to-point
• multi-access
10. Which statement is true about the running configuration file in a Cisco IOS device?
• It affects the operation of the device immediately when modified.
• It is stored in NVRAM.
• It should be deleted using the erase running-config command.
• It is automatically saved when the router reboots.
11. Refer to the exhibit. Host C is able to ping 127.0.0.1 successfully, but is unable to communicate with hosts A and B in the organization. What is the likely cause of the problem?
• Hosts A and B are not on the same subnet as host C.
• The IP addresses on the router serial interfaces are wrong.
• The subnet mask on host C is improperly configured.
• The FastEthernet interface fa0/0 of router 1 is wrongly configured.
12. A host is transmitting a video over the network. How does the transport layer allow this host to use multiple applications to transmit other data at the same time as the video transmission?
• It uses error control mechanisms.
• It uses a connectionless protocol only for multiple simultaneous transmissions.
• It uses multiple Layer 2 source addresses.
• It uses multiple port numbers.
13. Refer to the exhibit. PC1 is unable to access PC2. To troubleshoot this problem, the technician needs to confirm that the next hop interface is operational. Which default gateway address should the technician ping from PC1 to confirm this?
• 10.0.0.254
• 192.168.0.249
• 192.168.0.250
• 10.0.1.254
14. Refer to the exhibit. Cable 1 and Cable 2 are wired for specific physical layer requirements. Which three segments use Cable 2? (Choose three.)
• Segment 1
• Segment 2
• Segment 3
• Segment 4
• Segment 5
• Segment 6
15. Refer to the exhibit. Which two facts can be determined about the topology? (Choose two.)
• Three networks are needed.
• Two logical address ranges are required.
• A single broadcast domain is present.
• Three collision domains are present.
• Four networks are needed.
16. Refer to the exhibit. Which three statements are true about the IP configuration that is displayed? (Choose three.)
• The assigned address is a private address.
• The PC cannot communicate with the DNS server.
• The network can have 126 hosts.
• The prefix of the computer address is /26.
• The IP address is routable on the Internet.
• The IP address is a multicast address. 17. Which password restricts Telnet access to the router?
• enable
• enable secret
• console
• VTY
18. Refer to the exhibit. To create the initial configuration, a network technician connected host A to the router using the connection that is shown. Which statement is true about this connection?
• It terminates at the Ethernet port of the router.
• It provides out-of-band console access.
• It terminates at the serial interface of the router.
• It requires a Telnet client on host A to access the router. 19. Which device should be used for routing a packet to a remote network?
• access switch
• DHCP server
• hub
• router
20. Refer to the exhibit. The serial interface of the router was configured with the use of the commands that are shown. The router cannot ping the router that is directly connected to interface serial 0/0/0. What should the network technician do to solve this problem?
• Configure the description at interface serial 0/0/0.
• Configure an IP address on interface serial 0/0/0.
• Remove the no shutdown command at interface serial 0/0/0
• Reboot the router.
21. Refer to the exhibit. In a network, host A is sending data segments to host B. The flow control of the segments that are being exchanged is displayed. Which two statements are true about this communication? (Choose two.)
• The initial window size is determined via the two-way handshake.
• The window size for the TCP session that is represented is initially set to 3000 bytes.
• Acknowledgment number 3001 indicates that host A will send the next segment with sequence number 3001.
• Host B expects that the next received segment number will be 3000.
• No more acknowledgments will be exchanged.
22. Refer to the exhibit. The network administrator wants to remotely access the CLI of the router from PC1 using modem 1. Which port of the router should be connected to modem 2 to enable this access?
• console
• Ethernet
• auxiliary
• serial 23. Which OSI layer uses a connection-oriented protocol to ensure reliable delivery of data?
• application layer
• presentation layer
• session layer
• transport layer 24. What are two functions of the data link layer? (Choose two.)
• It segments and reorders the data.
• It exchanges data between programs that are running on the source and destination hosts.
• It controls how data is placed onto the media.
• It generates signals to represent the bits in each frame.
• It encapsulates each packet with a header and a trailer to transfer it across the local media. 25. Refer to the exhibit. Which list refers only to end devices?
• D,E,F,G
• A,H,B,C
• A,D,E,F
• A,D,E,G
26. Refer to the exhibit. The diagram represents the process of sending e-mail between clients. Which list correctly identifies the component or protocol used at each numbered stage of the diagram?
• 1.MUA 2.MDA 3.MTA 4.SMTP 5.MTA 6.POP 7.MDA 8.MUA
• 1.MUA 2.POP 3.MDA 4.SMTP 5.MTA 6.MDA 7.SMTP 8.MUA
• 1.MUA 2.POP 3.SMTP 4.MDA 5.MTA 6.SMTP 7.POP 8.MUA
• 1.MUA 2.SMTP 3.MTA 4.SMTP 5.MTA 6.MDA 7.POP 8.MUA
27. Refer to the exhibit. Host B was powered off. What change will occur in the MAC table of the switch?
The table will remain unaffected.
• The switch will remove the MAC address at Fa0/19 immediately.
• The switch will retain the MAC address until host B is powered on again.
• The switch will rebuild the MAC table by assigning the FFFF.FFFF.FFFF address to port Fa0/19.
28. Refer to the exhibit. A technician has connected the PC to the switch using a Category 6 UTP cable. Which two statements are true about this connection? (Choose two.)
• The cable that is used is an Ethernet crossover cable.
• The transmit pin of the cable is terminated to the receive pin.
• The maximum distance between the switch and the PC can be 100 m.
• The maximum supported bandwidth is 1000 Mb/s.
• The Category 6 cable simulates a point-to-point WAN link and is unusable for this type of connection.
29. Refer to the exhibit. A host is using NAT to connect to the Internet. Which three IP addresses enable this connection? (Choose three.)
• 10.1.1.63
• 10.1.1.37
• 10.1.1.39
• 10.1.1.32
• 10.1.1.60
• 10.1.1.2 30. Refer to the exhibit. A PC is communicating with another PC on a remote network. The two networks are connected by three routers. Which action will help to identify the path between the hosts?
• Use the ipconfig command at the host.
• Use the ipconfig/all command at the destination.
• Use the tracert command at the host.
• Use the ping command at the destination.
31. An organization wants to create a subnet of the IP network 172.16.0.0. This subnet will accommodate 1000 hosts. Which subnet mask should be assigned to this network?
• 255.255.0.0
• 255.255.248.0
• 255.255.252.0
• 255.255.254.0
• 255.255.255.0
• 255.255.255.128
32. Refer to the exhibit. A host is connected to hub 1. Which combination of IP address, subnet mask, and default gateway can allow this host to function in the network?
• IP address: 172.16.31.36 Subnet mask: 255.255.255.240 Default gateway: 172.16.31.35
• IP address: 172.16.31.63 Subnet mask: 255.255.255.224 Default gateway: 172.16.31.35
IP address: 172.16.31.29 Subnet mask: 255.255.255.248 Default gateway: 172.16.31.35
• IP address: 172.16.31.32 Subnet mask: 255.255.255.224 Default gateway: 172.16.31.35
• IP address: 172.16.31.29 Subnet mask: 255.255.255.240 Default gateway: 172.16.30.1
• IP address: 172.16.31.37 Subnet mask: 255.255.255.224 Default gateway: 172.16.31.35
33. Refer to the exhibit. A technician uses the nslookup command on the PC and views the output that is displayed in the exhibit. What is the IP address of the primary domain name server configured at the host? (Choose two.)
• 192.168.1.99
• 192.168.2.100
• 10.10.10.32
• 192.168.1.5
• the IP address of the website resolver1.xyz.local
34. Which OSI layer offers ordered data reconstruction services?
• application layer
• network layer
• presentation layer
• session layer
• transport layer
35. Refer to the exhibit. All devices in the network use default configurations. How many logical address ranges are required in this topology?
• 2
• 3
• 4
• 5
• 6
36. The network administrator wants to install a private application on a server. Which range of port numbers is normally assigned to this application to make it accessible by clients?
• 0 to 255
• 49152 to 65535
• 1024 to 49151
• 0 to 1023
37. Because of a security violation, the router password must be changed. What information can be learned from these configuration entries? (Choose two.)
• Router(config)# line vty 0 4
Router(config-line)# password arj15
Router(config-line)# login
• This configuration allows users to connect by using a modem.
• Users must specify which line, 0 or 4, they wish to connect to when making a connection.
• This configuration allows users to connect to the router via the use of the telnet command.
• This configuration allows five users to make simultaneous connections to this router.
• The configured password is automatically encrypted on the router.
38. Refer to the exhibit. Each media link is labeled. What type of cable should be used to connect the different devices?
• Connection 1 - rollover cable Connection 2 - straight-through cable Connection 3 - crossover cable
• Connection 1 - straight-through cable Connection 2 - crossover cable Connection 3 - rollover cable
• Connection 1 - crossover cable Connection 2 - rollover cable Connection 3 - straight-through cable
• Connection 1 - crossover cable Connection 2 - straight-through cable Connection 3 - rollover cable
• Connection 1 - straight-through cable Connection 2 - straight-through cable Connection 3 - straight-through cable
39. Which two types of media are useful for connecting two devices separated by a distance of 500 meters? (Choose two.)
• 10 BASE-T
• 1000 BASE-TX
• 10 BASE-2
• 1000 BASE LX
• 1000 BASE-SX 40. Which information is used by the router to determine the path between the source and destination hosts?
• the host portion of the IP address
• the network portion of the IP address
• host default gateway address
• the MAC address
41. Refer to the exhibit. What two facts can be determined from the session information that is displayed? (Choose two.)
• This exchange is part of the three-way handshake.
• The destination port indicates that a Telnet session has been initiated.
• The source port does not support communication with the destination port that is listed.
• The destination port indicates that an SMTP session has been initiated.
• The protocol is a connection-oriented protocol.
42. Refer to the exhibit. Host A is accessing multiple servers. Which combination of port number and address will uniquely identify a particular process running on a specific server?
• MAC address of the server and port number of the service
• IP address of the host and port number of the service
• MAC address of the host and port number of the service
• IP address of the server and port number of the service
43. A network technician wants to configure an IP address on a router interface by using the ip address 192.168.1.0 255.255.255.0 command. Which prompt should the technician see when entering this command?
• Router>
• Router(config-if)#
• Router#
• Router(config)# 44. Refer to the exhibit. Host X is unable to communicate with host Y. Which command can be run at host X to determine which intermediary device is responsible for this failure?
• telnet 192.168.1.1
• ping 192.168.1.1
• ftp 192.168.1.1
• tracert 192.168.1.1
45. Refer to the exhibit. In a network, PC1 sends a message to PC2. The frame received at PC2 is shown. What information in this frame determines the correct destination application?
• timing and synchronization bits
• destination and source physical addresses
• destination and source logical network addresses
• destination and source process numbers
46. An organization has been assigned network ID 10.10.128.0 and subnet mask 255.255.224.0. Which IP address range can be used for this organization?
• 10.10.128.0 to 10.10.160.255
• 10.10.128.0 to 10.10.159.255
• 10.10.128.0 to 10.10.192.255
• 10.10.128.0 to 10.10.0.159
• 10.10.128.0 to 10.10.159.0
47. What is the effect of using the Router# copy running-config startup-config command on a router?
• The contents of ROM will change.
• The contents of RAM will change.
• The contents of NVRAM will change.
• The contents of flash will change.
48. Which three IPv4 addresses represent valid host addresses for a subnet? (Choose three.)
• 10.1.12.79/28
• 10.1.12.113/28
• 10.1.12.32/28
• 10.1.11.5/27
• 10.1.11.97/27
• 10.1.11.128/27
49. Refer to the exhibit. The NAT functionality of the router is enabled to provide Internet access to the PC. However, the PC is still unable to access the Internet. Which IP address should be changed to 209.165.201.1 to enable the PC to access the Internet?
• 192.168.1.191
• 192.168.1.101
• 192.168.1.1
• 192.168.1.254
50. Which three statements are true about network layer addressing? (Choose three.)
• It uniquely identifies each host.
• It assists in forwarding packets across internetworks.
• It uses a logical 32-bit IPv4 address.
• It is not a configurable address.
• It is a physical address.
• It identifies the host from the first part of the address.
CCNA 1 Chapter 11
1. Users in the network are experiencing slow response time when doing file transfers to a remote server. What command could be issued to determine if the router has experienced any input or output errors?
show running-config
show startup-config
show interfaces
show ip route
show version
show memory
2. Refer to the exhibit. A technician applies the configuration in the exhibit to a clean router. To verify the configuration, the technician issues the show running-config command in the CLI session with the router. What lines should the technician expect to see in the router output from the show running-config command?
enable password classline console 0password ccna
enable secret ciscoenable password classline console 0password ccna
enable secret 5 $1$v0/3$QyQWmJyT7zCa/yaBRasJm0enable password classline console 0password ccna
enable secret ciscoenable password 7 14141E0A1F17line console 0password 7 020507550A
enable secret 5 $1$v0/3$QyQWmJyT7zCa/yaBRasJm0enable password 7 14141E0A1F17line console 0password 7 020507550A
3. Refer to the exhibit. A network administrator on HostA has problems accessing the FTP server. Layer three connectivity testing was successful from HostA to the S1 interface of RouterB. Which set of commands will allow the network administrator to telnet to RouterB and run debug commands?
RouterB(config)# enable secret class
RouterB(config)# line vty 0 4
RouterB(config-if)# login
RouterB(config)# enable secret class
RouterB(config)# line vty 0 2
RouterB(config-vty)# password cisco
RouterB(config-vty)# login
RouterB(config)# enable secret class
RouterB(config)# line vty 0
RouterB(config-line)# password cisco
RouterB(config-line)# login
RouterB(config)# enable secret class
RouterB(config)# line aux 0
RouterB(config-line)# password cisco
RouterB(config-line)# login
RouterB(config)# enable secret class
RouterB(config)# line aux 0
RouterB(config-vty)# password cisco
RouterB(config-vty)# login
4. Refer to the exhibit. The output is shown for the show ip route command executed on Router A. What does the IP address 192.168.2.2 represent?
Gateway for the 192.168.1.0 network
Gateway for the 192.168.3.0 network
IP assigned to the serial port on Router A
IP assigned to the serial port on Router B
5. What command is used to change the default router name to Fontana?
Router# name Fontana
Router# hostname Fontana
Router(config)# name Fontana
Router(config)# hostname Fontana
6. The serial connection shown in the graphic needs to be configured. Which configuration commands must be made on the Sydney router to establish connectivity with the Melbourne site? (Choose three.)
Sydney(config-if)# ip address 201.100.53.2 255.255.255.0
Sydney(config-if)# no shutdown
Sydney(config-if)# ip address 201.100.53.1 255.255.255.224
Sydney(config-if)# clock rate 56000
Sydney(config-if)# ip host Melbourne 201.100.53.2
7. Refer to the exhibit. What additional command is required to allow remote access to this switch?
NA-SW1(config-if)# no shutdown
NA-SW1(config)# enable password password
NA-SW1(config)# ip default-gateway address
NA-SW1(config-if)# description description
8. When network services fail, which port is most often used to access a router for management purposes?
AUX
Ethernet
Console
Telnet
SSH
9. A network administrator needs to keep the user ID, password, and session contents private when establishing remote CLI connectivity with a router to manage it. Which access method should be chosen?
Telnet
Console
AUX
SSH
10. In a Cisco router, when do changes made to the running-configuration take effect?
after a system restart
as the commands are entered
when logging off the system
when the configuration is saved to the startup-configuration
11. Refer to the exhibit. Which names correctly identify the CLI mode represented by the prompt for Switch-East4#? (Choose two.)
line configuration mode
user executive mode
global configuration mode
privileged executive mode
interface configuration mode
enable mode
12. Which three terms correctly define the forms of help available within the Cisco IOS? (Choose three.)
hot keys
context-check
context-sensitive
structured check
command override
command syntax check
13. Which combination of keys would be used at the CLI prompt to interrupt a ping or traceroute process?
Ctrl-C
Ctrl-P
Ctrl-R
Ctrl-Shift-6
Ctrl-Z
14. Refer to the exhibit. What command will place the router into the correct mode to configure an appropriate interface to connect to a LAN?
UBAMA# configure terminal
UBAMA(config)# line vty 0 4
UBAMA(config)# line console 0
UBAMA(config)# interface Serial 0/0/0
UBAMA(config)# interface FastEthernet 0/1
15. On a Cisco router, which interface would be used to make the initial configuration?
Console Port
16. Refer to the exhibit. A student is responsible for the IP addressing, configuration and connectivity testing of the network shown in the graphic. A ping from host B to host C results in a destination unreachable but a ping from host B to host A was successful. What two reasons could account for this failure based on the graphic and partial router output for the Dallas router? (Choose two.)
The host A is turned off.
The Fa0/0 interface on Dallas is shutdown.
The LAN cable is disconnected from host B.
The S0/0/1 IP address of Dallas is improperly configured.
The Fa0/0 interface on Dallas is in a different subnet than host B.
The clock rate is missing on the serial link between Dallas and NYC.
show running-config
show startup-config
show interfaces
show ip route
show version
show memory
2. Refer to the exhibit. A technician applies the configuration in the exhibit to a clean router. To verify the configuration, the technician issues the show running-config command in the CLI session with the router. What lines should the technician expect to see in the router output from the show running-config command?
enable password classline console 0password ccna
enable secret ciscoenable password classline console 0password ccna
enable secret 5 $1$v0/3$QyQWmJyT7zCa/yaBRasJm0enable password classline console 0password ccna
enable secret ciscoenable password 7 14141E0A1F17line console 0password 7 020507550A
enable secret 5 $1$v0/3$QyQWmJyT7zCa/yaBRasJm0enable password 7 14141E0A1F17line console 0password 7 020507550A
3. Refer to the exhibit. A network administrator on HostA has problems accessing the FTP server. Layer three connectivity testing was successful from HostA to the S1 interface of RouterB. Which set of commands will allow the network administrator to telnet to RouterB and run debug commands?
RouterB(config)# enable secret class
RouterB(config)# line vty 0 4
RouterB(config-if)# login
RouterB(config)# enable secret class
RouterB(config)# line vty 0 2
RouterB(config-vty)# password cisco
RouterB(config-vty)# login
RouterB(config)# enable secret class
RouterB(config)# line vty 0
RouterB(config-line)# password cisco
RouterB(config-line)# login
RouterB(config)# enable secret class
RouterB(config)# line aux 0
RouterB(config-line)# password cisco
RouterB(config-line)# login
RouterB(config)# enable secret class
RouterB(config)# line aux 0
RouterB(config-vty)# password cisco
RouterB(config-vty)# login
4. Refer to the exhibit. The output is shown for the show ip route command executed on Router A. What does the IP address 192.168.2.2 represent?
Gateway for the 192.168.1.0 network
Gateway for the 192.168.3.0 network
IP assigned to the serial port on Router A
IP assigned to the serial port on Router B
5. What command is used to change the default router name to Fontana?
Router# name Fontana
Router# hostname Fontana
Router(config)# name Fontana
Router(config)# hostname Fontana
6. The serial connection shown in the graphic needs to be configured. Which configuration commands must be made on the Sydney router to establish connectivity with the Melbourne site? (Choose three.)
Sydney(config-if)# ip address 201.100.53.2 255.255.255.0
Sydney(config-if)# no shutdown
Sydney(config-if)# ip address 201.100.53.1 255.255.255.224
Sydney(config-if)# clock rate 56000
Sydney(config-if)# ip host Melbourne 201.100.53.2
7. Refer to the exhibit. What additional command is required to allow remote access to this switch?
NA-SW1(config-if)# no shutdown
NA-SW1(config)# enable password password
NA-SW1(config)# ip default-gateway address
NA-SW1(config-if)# description description
8. When network services fail, which port is most often used to access a router for management purposes?
AUX
Ethernet
Console
Telnet
SSH
9. A network administrator needs to keep the user ID, password, and session contents private when establishing remote CLI connectivity with a router to manage it. Which access method should be chosen?
Telnet
Console
AUX
SSH
10. In a Cisco router, when do changes made to the running-configuration take effect?
after a system restart
as the commands are entered
when logging off the system
when the configuration is saved to the startup-configuration
11. Refer to the exhibit. Which names correctly identify the CLI mode represented by the prompt for Switch-East4#? (Choose two.)
line configuration mode
user executive mode
global configuration mode
privileged executive mode
interface configuration mode
enable mode
12. Which three terms correctly define the forms of help available within the Cisco IOS? (Choose three.)
hot keys
context-check
context-sensitive
structured check
command override
command syntax check
13. Which combination of keys would be used at the CLI prompt to interrupt a ping or traceroute process?
Ctrl-C
Ctrl-P
Ctrl-R
Ctrl-Shift-6
Ctrl-Z
14. Refer to the exhibit. What command will place the router into the correct mode to configure an appropriate interface to connect to a LAN?
UBAMA# configure terminal
UBAMA(config)# line vty 0 4
UBAMA(config)# line console 0
UBAMA(config)# interface Serial 0/0/0
UBAMA(config)# interface FastEthernet 0/1
15. On a Cisco router, which interface would be used to make the initial configuration?
Console Port
16. Refer to the exhibit. A student is responsible for the IP addressing, configuration and connectivity testing of the network shown in the graphic. A ping from host B to host C results in a destination unreachable but a ping from host B to host A was successful. What two reasons could account for this failure based on the graphic and partial router output for the Dallas router? (Choose two.)
The host A is turned off.
The Fa0/0 interface on Dallas is shutdown.
The LAN cable is disconnected from host B.
The S0/0/1 IP address of Dallas is improperly configured.
The Fa0/0 interface on Dallas is in a different subnet than host B.
The clock rate is missing on the serial link between Dallas and NYC.
Subscribe to:
Posts (Atom)